관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Plastics — Determination of dynamic mechanical properties — Part 11: Glass transition temperature
| 분야 | ISO/TC 61/SC 5 : Physical-chemical properties |
|---|---|
| 적용범위 | This document specifies methods for determining a value of the glass transition temperature (Tg) from the dynamic mechanical properties measured during a linear temperature scan under heating conditions. The glass transition temperature is an indicator of the transition from a hard and relatively brittle glassy state to a rubbery or viscous liquid state in an amorphous polymer or in amorphous regions of a partially crystalline polymer. Usually referred to as dynamic mechanical analysis (DMA), the methods and their associated procedures can be applied to unreinforced and filled polymers, foams, rubbers, adhesives and fibre-reinforced plastics/composites. The methods are limited to materials that are inherently stable above Tg, i.e. amorphous materials that transform into a rubbery state or partially crystalline materials that keep their shape due to crystallinity. Different modes (e.g. flexure, torsion, shear, compression, tension) of dynamic mechanical analysis can be applied, as appropriate, to the form of the source material. Measured Tg values using instrumentation can vary as a result of material characteristics and/or the test set-up. The temperature sensor in a DMA instrument is not in contact with the test specimen and therefore measures temperature of the environment surrounding the specimen under test. The resulting data can vary with the heating rate applied. A procedure is included to take into account the thermal lag influencing the measured data. |
| 국제분류(ICS)코드 | 83.080.01 : 플라스틱 일반 |
| 페이지수 | 14 |
| Edition | 2 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ISO 6721-11:2019 | Plastics — Determination of dynamic mechanical properties — Part 11: Glass transition temperature | 2019-05-29 | 표준 |
| 2 | ISO 6721-11:2012 | Plastics — Determination of dynamic mechanical properties — Part 11: Glass transition temperature | 2012-03-21 | 구판 |
ISO/DIS 6721-10 - Plastics — Determination of dynamic mechanical properties — Part 10: Complex shear viscosity using a parallel-plate and a cone-and-plate oscillatory rheometer 상세보기
ISO 6721-10:2015 - Plastics — Determination of dynamic mechanical properties — Part 10: Complex shear viscosity using a parallel-plate oscillatory rheometer 상세보기
ISO 6721-8:2019 - Plastics — Determination of dynamic mechanical properties — Part 8: Longitudinal and shear vibration — Wave-propagation method 상세보기
ISO 6721-9:2019 - Plastics — Determination of dynamic mechanical properties — Part 9: Tensile vibration — Sonic-pulse propagation method 상세보기
ISO 6721-7:2019 - Plastics — Determination of dynamic mechanical properties — Part 7: Torsional vibration — Non-resonance method 상세보기
ISO 188:2011 - Rubber, vulcanized or thermoplastic — Accelerated ageing and heat resistance tests 상세보기
IEC 62631-3-2:2015 - Dielectric and resistive properties of solid insulating materials - Part 3-2: Determination of resistive properties (DC methods) - Surface resistance and surface resistivity 상세보기
ASTM D3801-19a - Standard Test Method for Measuring the Comparative Burning Characteristics of Solid Plastics in a Vertical Position 상세보기
ASTM D3763-18 - Standard Test Method for High Speed Puncture Properties of Plastics Using Load and Displacement Sensors 상세보기
ASTM E756-05(2017) - Standard Test Method for Measuring Vibration-Damping Properties of Materials 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
