관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Plastics — Determination of dynamic mechanical properties — Part 10: Complex shear viscosity using a parallel-plate oscillatory rheometer
| 분야 | ISO/TC 61/SC 5 : Physical-chemical properties |
|---|---|
| 적용범위 | ISO 6721-10:2015 specifies the general principles of a method for determining the dynamic rheological properties of polymer melts at angular frequencies typically in the range of 0,01 rad·s-1 to 100 rad·s-1 by means of an oscillatory rheometer with a parallel-plate geometry. Angular frequencies outside this range can also be used (see Note 1). The method is used to determine values of the following dynamic rheological properties: complex shear viscosity η*, dynamic shear viscosity η', the out-of-phase component of the complex shear viscosity η", complex shear modulus G*, shear loss modulus G", and shear storage modulus G'. It is suitable for measuring complex shear viscosity values typically up to ~10 MPa·s (see Note 2). NOTE 1 The angular-frequency measurement range is limited by the specification of the measuring instrument and also by the response of the specimen. When testing using angular frequencies lower than 0,1 rad·s?1, the test time can increase significantly as the time taken to obtain a single measurement is proportional to the reciprocal of the angular frequency. Consequently, when testing at low angular frequencies, degradation or polymerization of the specimen is more likely to occur and have an effect on the results. At high angular frequencies, the specimen can distort or fracture at the edge, consequently invalidating the test results. NOTE 2 The range of complex shear viscosity values that can be measured is dependent on the specimen dimensions and also the specification of the measuring instrument. For a specimen of given dimensions, the upper limit of the range is limited by the machine's torque capacity, angular-displacement resolution, and compliance. However, correction can be made for compliance effects. |
| 국제분류(ICS)코드 | 83.080.01 : 플라스틱 일반 |
| 페이지수 | 19 |
| Edition | 3 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ISO 6721-10:2015 | Plastics — Determination of dynamic mechanical properties — Part 10: Complex shear viscosity using a parallel-plate oscillatory rheometer | 2015-09-21 | 표준 |
| 2 | ISO 6721-10:1999 | Plastics — Determination of dynamic mechanical properties — Part 10: Complex shear viscosity using a parallel-plate oscillatory rheometer | 1999-12-16 | 구판 |
| 3 | ISO 6721-10:1997 | Plastics — Determination of dynamic mechanical properties — Part 10: Complex shear viscosity using a parallel-plate oscillatory rheometer | 1997-08-07 | 구판 |
| 4 | ISO/DIS 6721-10 | Plastics — Determination of dynamic mechanical properties — Part 10: Complex shear viscosity using a parallel-plate and a cone-and-plate oscillatory rheometer | 초안 |
ISO/DIS 6721-10 - Plastics — Determination of dynamic mechanical properties — Part 10: Complex shear viscosity using a parallel-plate and a cone-and-plate oscillatory rheometer 상세보기
ISO 6721-8:2019 - Plastics — Determination of dynamic mechanical properties — Part 8: Longitudinal and shear vibration — Wave-propagation method 상세보기
ISO 6721-9:2019 - Plastics — Determination of dynamic mechanical properties — Part 9: Tensile vibration — Sonic-pulse propagation method 상세보기
ISO 6721-7:2019 - Plastics — Determination of dynamic mechanical properties — Part 7: Torsional vibration — Non-resonance method 상세보기
ISO 6721-5:2019 - Plastics — Determination of dynamic mechanical properties — Part 5: Flexural vibration — Non-resonance method 상세보기
함께 구입한 상품이 존재하지 않습니다.
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
