관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Plastics — Determination of dynamic mechanical properties — Part 7: Torsional vibration — Non-resonance method
| 분야 | ISO/TC 61/SC 5 : Physical-chemical properties |
|---|---|
| 적용범위 | This document describes a torsional, non-resonance method for determining the components of the shear complex modulus G* of solid polymers in the form of bars or rods at frequencies typically in the range 0,001 Hz to 100 Hz. Higher-frequency measurements can be made, but significant errors in the dynamic properties measured are likely to result (see 10.2.1 and 10.2.2). The method is suitable for measuring dynamic storage moduli ranging from about 10 MPa, which is typical of values obtained for stiff rubbers, to values of about 10 GPa which are representative of fibre-reinforced plastics. Although materials with moduli less than 10 MPa can be studied, more accurate measurements of their dynamic properties can be made using simple shear (see ISO 6721-6) or torsional deformations of thin layers between parallel plates. This method is particularly suited to the measurement of loss factors greater than 0,02 and may therefore be conveniently used to study the variation of dynamic properties with temperature and frequency through most of the glass-rubber relaxation region (see ISO 6721‑1). The availability of data determined over wide ranges of both frequency and temperature enable master plots to be derived, using frequency-temperature shift procedures, which display dynamic properties over an extended frequency range at different temperatures. NOTE Although loss factors below 0,1 can be more accurately determined using the torsion pendulum (see ISO 6721‑2), the method described in this document enables a much wider and continuous frequency range to be covered. |
| 국제분류(ICS)코드 | 83.080.01 : 플라스틱 일반 |
| 페이지수 | 10 |
| Edition | 2 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ISO 6721-7:2019 | Plastics — Determination of dynamic mechanical properties — Part 7: Torsional vibration — Non-resonance method | 2019-04-16 | 표준 |
| 2 | ISO 6721-7:1996/Amd 1:2007 | Plastics — Determination of dynamic mechanical properties — Part 7: Torsional vibration — Non-resonance method — Amendment 1 | 2007-01-15 | 구판 |
| 3 | ISO 6721-7:1996 | Plastics — Determination of dynamic mechanical properties — Part 7: Torsional vibration — Non-resonance method | 1996-05-23 | 구판 |
ISO/DIS 6721-10 - Plastics — Determination of dynamic mechanical properties — Part 10: Complex shear viscosity using a parallel-plate and a cone-and-plate oscillatory rheometer 상세보기
ISO 6721-10:2015 - Plastics — Determination of dynamic mechanical properties — Part 10: Complex shear viscosity using a parallel-plate oscillatory rheometer 상세보기
ISO 6721-8:2019 - Plastics — Determination of dynamic mechanical properties — Part 8: Longitudinal and shear vibration — Wave-propagation method 상세보기
ISO 6721-9:2019 - Plastics — Determination of dynamic mechanical properties — Part 9: Tensile vibration — Sonic-pulse propagation method 상세보기
ISO 6721-5:2019 - Plastics — Determination of dynamic mechanical properties — Part 5: Flexural vibration — Non-resonance method 상세보기
함께 구입한 상품이 존재하지 않습니다.
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
