관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Standard Test Method for Short-Beam Strength of Polymer Matrix Composite Materials and Their Laminates
| 분야 | |
|---|---|
| 적용범위 | 1.1?This test method determines the short-beam strength of high-modulus fiber-reinforced composite materials. The specimen is a short beam machined from a curved or a flat laminate up to 6.00 mm [0.25 in.] thick. The beam is loaded in three-point bending. 1.2?Application of this test method is limited to continuous- or discontinuous-fiber-reinforced polymer matrix composites, for which the elastic properties are balanced and symmetric with respect to the longitudinal axis of the beam. 1.3?Units?The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.3.1?Within the text, the inch-pound units are shown in brackets. 1.4?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | |
| 페이지수 | 10 |
| Edition | 22 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM D2344/D2344M-22 | Standard Test Method for Short-Beam Strength of Polymer Matrix Composite Materials and Their Laminates | 2022-07-15 | 표준 |
| 2 | ASTM D2344/D2344M-22 REDLINE | Standard Test Method for Short-Beam Strength of Polymer Matrix Composite Materials and Their Laminates | 2022-07-15 | 표준 |
| 3 | ASTM D2344/D2344M-16 REDLINE | Standard Test Method for Short-Beam Strength of Polymer Matrix Composite Materials and Their Laminates | 2016-07-01 | 구판 |
| 4 | ASTM D2344/D2344M-16 | Standard Test Method for Short-Beam Strength of Polymer Matrix Composite Materials and Their Laminates | 2016-07-01 | 구판 |
| 5 | ASTM D2344/D2344M-13 | Standard Test Method for Short-Beam Strength of Polymer Matrix Composite Materials and Their Laminates | 2013-10-01 | 구판 |
| 6 | ASTM D2344/D2344M-00(2006) | Standard Test Method for Short-Beam Strength of Polymer Matrix Composite Materials and Their Laminates | 2006-01-15 | 구판 |
| 7 | ASTM D2344/D2344M-00e1 | Standard Test Method for Short-Beam Strength of Polymer Matrix Composite Materials and Their Laminates | 2000-03-10 | 구판 |
관련상품이 존재하지 않습니다.
ASTM D1623-17(2023) - Standard Test Method for Tensile and Tensile Adhesion Properties of Rigid Cellular Plastics 상세보기
ASTM D1876-08(2023) - Standard Test Method for Peel Resistance of Adhesives (T-Peel Test) 상세보기
ASTM D256-23e1 - Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics 상세보기
ASTM D3165-07(2023) - Standard Test Method for Strength Properties of Adhesives in Shear by Tension Loading of Single-Lap-Joint Laminated Assemblies 상세보기
ASTM D5630-22 - Standard Test Method for Ash Content in Plastics 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
