관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics
| 분야 | 08.01 : 플라스틱 (Ⅰ) | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 적용범위 | 1.1?These test methods cover the determination of the resistance of plastics to “standardized” (see Note 1) pendulum-type hammers, mounted in “standardized” machines, in breaking standard specimens with one pendulum swing (see Note 2). The standard tests for these test methods require specimens made with a milled notch (see Note 3). In Test Methods A, C, and D, the notch produces a stress concentration that increases the probability of a brittle, rather than a ductile, fracture. In Test Method E, the impact resistance is obtained by reversing the notched specimen 180° in the clamping vise. The results of all test methods are reported in terms of energy absorbed per unit of specimen width or per unit of cross-sectional area under the notch. (See Note 4.) Note 1:?The machines with their pendulum-type hammers have been “standardized” in that they must comply with certain requirements, including a fixed height of hammer fall that results in a substantially fixed velocity of the hammer at the moment of impact. However, hammers of different initial energies (produced by varying their effective weights) are recommended for use with specimens of different impact resistance. Moreover, manufacturers of the equipment are permitted to use different lengths and constructions of pendulums with possible differences in pendulum rigidities resulting. (See Section 5.) Be aware that other differences in machine design may exist. The specimens are “standardized” in that they are required to have one fixed length, one fixed depth, and one particular design of milled notch. The width of the specimens is permitted to vary between limits. Note 2:?Results generated using pendulums that utilize a load cell to record the impact force and thus impact energy, may not be equivalent to results that are generated using manually or digitally encoded testers that measure the energy remaining in the pendulum after impact. Note 3:?The notch in the Izod specimen serves to concentrate the stress, minimize plastic deformation, and direct the fracture to the part of the specimen behind the notch. Scatter in energy-to-break is thus reduced. However, because of differences in the elastic and viscoelastic properties of plastics, response to a given notch varies among materials. A measure of a plastic's “notch sensitivity” may be obtained with Test Method D by comparing the energies to break specimens having different radii at the base of the notch. Note 4:?Caution must be exercised in interpreting the results of these standard test methods. The following testing parameters may affect test results significantly: Method of fabrication, including but not limited to processing technology, molding conditions, mold design, and thermal treatments; Method of notching; Speed of notching tool; Design of notching apparatus; Quality of the notch; Time between notching and test; Test specimen thickness, Test specimen width under notch, and Environmental conditioning. 1.2?The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only. 1.3?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Note 5:?These test methods resemble ISO 180:1993 in regard to title only. The contents are significantly different. 1.4?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
|||||||||||
| 국제분류(ICS)코드 | 29.035.20 : 유리 및 세라믹 절연 재료 | |||||||||||
| 페이지수 | 20 | |||||||||||
| Edition | 23e1 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM D256-23 | Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics | 2023-03-15 | 구판 |
| 2 | ASTM D256-23e1 | Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics | 2023-03-15 | 표준 |
| 3 | ASTM D256-10(2018) | Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics | 2018-11-01 | 구판 |
| 4 | ASTM D256-10e1 | Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics | 2010-05-01 | 구판 |
| 5 | ASTM D256-10 | Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics | 2010-05-01 | 구판 |
| 6 | ASTM D256-06ae1 | Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics | 2006-12-01 | 구판 |
| 7 | ASTM D256-06a | Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics | 2006-12-01 | 구판 |
| 8 | ASTM D256-06 | Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics | 2006-03-15 | 구판 |
| 9 | ASTM D256-05a | Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics | 2005-11-01 | 구판 |
| 10 | ASTM D256-05 | Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics | 2005-01-01 | 구판 |
| 11 | ASTM D256-04 | Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics | 2004-05-01 | 구판 |
| 12 | ASTM D256-03 | Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics | 2003-12-01 | 구판 |
| 13 | ASTM D256-02e1 | Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics | 2002-08-10 | 구판 |
| 14 | ASTM D256-02 | Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics | 2002-08-10 | 구판 |
| 15 | ASTM D256-00e1 | Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics | 2000-11-10 | 구판 |
관련상품이 존재하지 않습니다.
ASTM D1238-23 REDLINE - Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer 상세보기
ASTM D638-22 - Standard Test Method for Tensile Properties of Plastics 상세보기
ASTM D5708-15(2020)e1 - Standard Test Methods for Determination of Nickel, Vanadium, and Iron in Crude Oils and Residual Fuels by Inductively Coupled Plasma (ICP) Atomic Emission Spectrometry 상세보기
ASTM D664-18e2 - Standard Test Method for Acid Number of Petroleum Products by Potentiometric Titration 상세보기
ASTM D1500-12(2017) - Standard Test Method for ASTM Color of Petroleum Products (ASTM Color Scale) 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
