관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Standard Test Method for Ash Content in Plastics
| 분야 | 08.03 : 플라스틱 (Ⅲ) |
|---|---|
| 적용범위 | 1.1?This test method was developed to determine the inorganic content of plastics by destructive ashing procedures. Ash levels of 0.01?% or above are covered by this test method. 1.2?These ashing procedures are used only to quantify the residual solids in the polymer and can not be used to identify the individual chemical components of the ash, qualitatively. 1.3?This test method is limited to those materials (including glass) that are stable to 900°C. Test Method D2584 is recommended for unknown samples, and in instances where fusion of the inorganic portions may be of concern. 1.4?Fluorinated polymers and polymers containing halogenated components have not been included in these procedures. 1.5?Two procedures for determining the inorganic residue in plastics are listed as follows: 1.5.1?Procedure A, Muffle-Furnace Technique? For 5 ? 50 gram samples. Samples are flamed over a burner prior to being ashed in a muffle furnace. 1.5.2?Procedure B, Rapid-Ash Muffle-Furnace Technique? For 2?10 gram samples. Samples are ignited and ashed in a muffle furnace. Note 1:?For more efficient ashing, the plastic sample should be in the form of powder or pellet. Note 2:?This test method provides consistent results of filler content for a specific filler in a specific resin. However, this method may not provide the absolute filler content in all cases. This includes polymers filled with CaCO3, nano clays, and Carbon Black. Note 3:?Procedure B is equivalent to ISO 3451/1-(E), Method A. 1.6?The values stated in SI units are to be regarded as the standard. 1.7?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. See Section 9 for specific precautionary statements. 1.8?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | 83.080.20 : 열가소성 수지재 |
| 페이지수 | 5 |
| Edition | 22 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM D5630-22 | Standard Test Method for Ash Content in Plastics | 2022-11-01 | 표준 |
| 2 | ASTM D5630-13 REDLINE | Standard Test Method for Ash Content in Plastics | 2013-04-01 | 구판 |
| 3 | ASTM D5630-13 | Standard Test Method for Ash Content in Plastics (Withdrawn 2022) | 2013-04-01 | 구판 |
| 4 | ASTM D5630-06 | Standard Test Method for Ash Content in Plastics | 2006-09-01 | 구판 |
| 5 | ASTM D5630-94 | Standard Test Method for Ash Content in Thermoplastics | 2001-09-10 | 구판 |
| 6 | ASTM D5630-01 | Standard Test Method for Ash Content in Thermoplastics | 2001-09-10 | 구판 |
관련상품이 존재하지 않습니다.
ASTM D1238-23 REDLINE - Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer 상세보기
ASTM D2344/D2344M-22 REDLINE - Standard Test Method for Short-Beam Strength of Polymer Matrix Composite Materials and Their Laminates 상세보기
ASTM D1623-17(2023) - Standard Test Method for Tensile and Tensile Adhesion Properties of Rigid Cellular Plastics 상세보기
ASTM D1876-08(2023) - Standard Test Method for Peel Resistance of Adhesives (T-Peel Test) 상세보기
ASTM D256-23e1 - Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
