관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
구판
판매
Standard Test Method for Shear Strength of Plastics by Punch Tool
| 분야 | 08.01 : 플라스틱 (Ⅰ) |
|---|---|
| 적용범위 | 1.1 This test method covers the procedure for determining the shear strength of plastics in the form of sheets, plates, and molded shapes in thicknesses from 1.27 to 12.7 mm (0.050 to 0.500 in.). 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Note 1: There is no known ISO equivalent to this standard. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | 83.080.01 : 플라스틱 일반 |
| 페이지수 | 4 |
| Edition | 17 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM D732-24 | Standard Test Method for Shear Strength of Plastics by Punch Tool | 2024-08-01 | 표준 |
| 2 | ASTM D732-24 REDLINE | Standard Test Method for Shear Strength of Plastics by Punch Tool | 2024-08-01 | 표준 |
| 3 | ASTM D732-17 | Standard Test Method for Shear Strength of Plastics by Punch Tool | 2017-05-01 | 구판 |
| 4 | ASTM D732-17 REDLINE | Standard Test Method for Shear Strength of Plastics by Punch Tool | 2017-05-01 | 구판 |
| 5 | ASTM D732-10 | Standard Test Method for Shear Strength of Plastics by Punch Tool | 2010-04-01 | 구판 |
| 6 | ASTM D732-09 | Standard Test Method for Shear Strength of Plastics by Punch Tool | 2009-10-15 | 구판 |
| 7 | ASTM D732-99 | Standard Test Method for Shear Strength of Plastics by Punch Tool | 2002-04-10 | 구판 |
| 8 | ASTM D732-02 | Standard Test Method for Shear Strength of Plastics by Punch Tool | 2002-04-10 | 구판 |
관련상품이 존재하지 않습니다.
ASTM D696-16 - Standard Test Method for Coefficient of Linear Thermal Expansion of Plastics Between −30°C and 30°C with a Vitreous Silica Dilatometer 상세보기
ASTM D638-14 - Standard Test Method for Tensile Properties of Plastics 상세보기
ASTM D695-15 - Standard Test Method for Compressive Properties of Rigid Plastics 상세보기
ASTM D1621-16 - Standard Test Method for Compressive Properties of Rigid Cellular Plastics 상세보기
ASTM D1623-17 - Standard Test Method for Tensile and Tensile Adhesion Properties of Rigid Cellular Plastics 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
