관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
구판
판매
Standard Test Method for Tensile Properties of Plastics
| 분야 | 08.01 : 플라스틱 (Ⅰ) |
|---|---|
| 적용범위 | 1.1 This test method covers the determination of the tensile properties of unreinforced and reinforced plastics in the form of standard dumbbell-shaped test specimens when tested under defined conditions of pretreatment, temperature, humidity, and testing machine speed. 1.2 This test method is applicable for testing materials of any thickness up to 14 mm (0.55 in.). However, for testing specimens in the form of thin sheeting, including film less than 1.0 mm (0.04 in.) in thickness, ASTM standard D882 is the preferred test method. Materials with a thickness greater than 14 mm (0.55 in.) shall be reduced by machining. 1.3 This test method includes the option of determining Poisson's ratio at room temperature. Note 1: This standard and ISO 527-1 address the same subject matter, but differ in technical content. Note 2: This test method is not intended to cover precise physical procedures. It is recognized that the constant rate of crosshead movement type of test leaves much to be desired from a theoretical standpoint, that wide differences may exist between rate of crosshead movement and rate of strain between gage marks on the specimen, and that the testing speeds specified disguise important effects characteristic of materials in the plastic state. Further, it is realized that variations in the thicknesses of test specimens, which are permitted by these procedures, produce variations in the surface-volume ratios of such specimens, and that these variations may influence the test results. Hence, where directly comparable results are desired, all samples should be of equal thickness. Special additional tests should be used where more precise physical data are needed. Note 3: This test method may be used for testing phenolic molded resin or laminated materials. However, where these materials are used as electrical insulation, such materials should be tested in accordance with Test Methods D229 and Test Method D651. Note 4: For tensile properties of resin-matrix composites reinforced with oriented continuous or discontinuous high modulus >20-GPa (>3.0 × 106-psi) fibers, tests shall be made in accordance with Test Method D3039/D3039M. 1.4 Test data obtained by this test method have been found to be useful in engineering design. However, it is important to consider the precautions and limitations of this method found in Note 2 and Section 4 before considering these data for engineering design. 1.5 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
| 국제분류(ICS)코드 | 83.080.01 : 플라스틱 일반 |
| 페이지수 | 17 |
| Edition | 14 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM D638-22 | Standard Test Method for Tensile Properties of Plastics | 2022-07-01 | 표준 |
| 2 | ASTM D638-22 REDLINE | Standard Test Method for Tensile Properties of Plastics | 2022-07-01 | 표준 |
| 3 | ASTM D638-14 | Standard Test Method for Tensile Properties of Plastics | 2014-12-15 | 구판 |
| 4 | ASTM D638-14 REDLINE | Standard Test Method for Tensile Properties of Plastics | 2014-12-15 | 구판 |
| 5 | ASTM D638-10 | Standard Test Method for Tensile Properties of Plastics | 2010-05-15 | 구판 |
| 6 | ASTM D638-08 | Standard Test Method for Tensile Properties of Plastics | 2008-04-01 | 구판 |
| 7 | ASTM D638-03 | Standard Test Method for Tensile Properties of Plastics | 2003-12-01 | 구판 |
| 8 | ASTM D638-02a | Standard Test Method for Tensile Properties of Plastics | 2002-11-10 | 구판 |
| 9 | ASTM D638-00 | Standard Test Method for Tensile Properties of Plastics | 2002-04-10 | 구판 |
| 10 | ASTM D638-99 | Standard Test Method for Tensile Properties of Plastics | 2002-04-10 | 구판 |
| 11 | ASTM D638-01 | Standard Test Method for Tensile Properties of Plastics | 2002-04-10 | 구판 |
| 12 | ASTM D638-02 | Standard Test Method for Tensile Properties of Plastics | 2002-04-10 | 구판 |
관련상품이 존재하지 않습니다.
ASTM D790-17 - Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials 상세보기
ASTM D695-15 - Standard Test Method for Compressive Properties of Rigid Plastics 상세보기
ASTM D256-10(2018) - Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics 상세보기
ASTM D785-08(2015) - Standard Test Method for Rockwell Hardness of Plastics and Electrical Insulating Materials 상세보기
ASTM D1894-14 - Standard Test Method for Static and Kinetic Coefficients of Friction of Plastic Film and Sheeting (Withdrawn 2023) 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
