관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
폐지
판매
Standard Test Method for Static and Kinetic Coefficients of Friction of Plastic Film and Sheeting (Withdrawn 2023)
| 분야 | 08.01 : 플라스틱 (Ⅰ) |
|---|---|
| 적용범위 | 1.1 This test method covers determination of the coefficients of starting and sliding friction of plastic film and sheeting when sliding over itself or other substances at specified test conditions. The procedure permits the use of a stationary sled with a moving plane, or a moving sled with a stationary plane. Both procedures yield the same coefficients of friction values for a given sample. Note 1—For the frictional characteristics of plastic films partially wrapped around a cylinder, or capstan, see Test Method G143 under the jurisdiction of ASTM Subcommittee G02.50. 1.2 Test data obtained by this test method is relevant and appropriate for use in engineering design. 1.2.1 As an option to this test, coefficient of friction may be run at temperatures other than 23°C by heating only the plane while the sled is at ambient temperature. 1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For a specific precautionary statement, see the end of 6.5. Note 2—This test method is not equivalent to ISO 8295–1995, and results cannot be directly compared between the two methods. |
| 국제분류(ICS)코드 | 83.140.10 : 필름 및 시트 |
| 페이지수 | 7 |
| Edition | 14 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM D1894-14 REDLINE | Standard Test Method for Static and Kinetic Coefficients of Friction of Plastic Film and Sheeting | 2014-03-01 | 폐지 |
| 2 | ASTM D1894-14 | Standard Test Method for Static and Kinetic Coefficients of Friction of Plastic Film and Sheeting (Withdrawn 2023) | 2014-03-01 | 폐지 |
| 3 | ASTM D1894-11e1 | Standard Test Method for Static and Kinetic Coefficients of Friction of Plastic Film and Sheeting | 2011-09-01 | 구판 |
| 4 | ASTM D1894-11 | Standard Test Method for Static and Kinetic Coefficients of Friction of Plastic Film and Sheeting | 2011-09-01 | 구판 |
| 5 | ASTM D1894-08 | Standard Test Method for Static and Kinetic Coefficients of Friction of Plastic Film and Sheeting | 2008-11-01 | 구판 |
| 6 | ASTM D1894-06 | Standard Test Method for Static and Kinetic Coefficients of Friction of Plastic Film and Sheeting | 2006-05-01 | 구판 |
| 7 | ASTM D1894-00 | Standard Test Method for Static and Kinetic Coefficients of Friction of Plastic Film and Sheeting | 2001-03-10 | 구판 |
| 8 | ASTM D1894-01 | Standard Test Method for Static and Kinetic Coefficients of Friction of Plastic Film and Sheeting | 2001-03-10 | 구판 |
관련상품이 존재하지 않습니다.
ASTM D638-14 - Standard Test Method for Tensile Properties of Plastics 상세보기
ASTM D785-08(2015) - Standard Test Method for Rockwell Hardness of Plastics and Electrical Insulating Materials 상세보기
ASTM D790-17 - Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials 상세보기
ASTM D695-15 - Standard Test Method for Compressive Properties of Rigid Plastics 상세보기
ASTM D1505-18 - Standard Test Method for Density of Plastics by the Density-Gradient Technique 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
