관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
구판
판매
Standard Test Method for Tensile and Tensile Adhesion Properties of Rigid Cellular Plastics
| 분야 | 08.01 : 플라스틱 (Ⅰ) |
|---|---|
| 적용범위 | 1.1 This test method covers the determination of the tensile and tensile adhesion properties of rigid cellular materials in the form of test specimens of standard shape under defined conditions of temperature, humidity, and testing machine speed. 1.2 Tensile properties shall be measured using any of three types of specimens: 1.2.1 Type A shall be the preferred specimen in those cases where enough sample material exists to form the necessary specimen. 1.2.2 Type B shall be the preferred specimen when only smaller specimens are available, as in sandwich panels, etc. 1.2.3 Type C shall be the preferred specimen for the determination of tensile adhesive properties of a cellular plastic to a substrate as in a sandwich panel (top and bottom substrate) or the bonding strength of a cellular plastic to a single substrate. 1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard. Note 1: There is no known ISO equivalent to this test method. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | 83.100 : 셀룰로이드 자재 |
| 페이지수 | 7 |
| Edition | 17 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM D1623-17(2023) | Standard Test Method for Tensile and Tensile Adhesion Properties of Rigid Cellular Plastics | 2023-05-01 | 표준 |
| 2 | ASTM D1623-17 | Standard Test Method for Tensile and Tensile Adhesion Properties of Rigid Cellular Plastics | 2017-05-01 | 구판 |
| 3 | ASTM D1623-17 REDLINE | Standard Test Method for Tensile and Tensile Adhesion Properties of Rigid Cellular Plastics | 2017-05-01 | 구판 |
| 4 | ASTM D1623-09 | Standard Test Method for Tensile and Tensile Adhesion Properties of Rigid Cellular Plastics | 2009-09-01 | 구판 |
| 5 | ASTM D1623-03 | Standard Test Method for Tensile and Tensile Adhesion Properties of Rigid Cellular Plastics | 2003-03-10 | 구판 |
| 6 | ASTM D1623-78(1995) | Standard Test Method for Tensile And Tensile Adhesion Properties Of Rigid Cellular Plastics | 1995-01-01 | 구판 |
관련상품이 존재하지 않습니다.
ASTM D1621-16 - Standard Test Method for Compressive Properties of Rigid Cellular Plastics 상세보기
ASTM D2126-15 - Standard Test Method for Response of Rigid Cellular Plastics to Thermal and Humid Aging 상세보기
ASTM C518-17 - Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Heat Flow Meter Apparatus 상세보기
ASTM C177-19 - Standard Test Method for Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the Guarded-Hot-Plate Apparatus 상세보기
ASTM D1622/D1622M-14 - Standard Test Method for Apparent Density of Rigid Cellular Plastics 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
