관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Plastics — Environmental aspects — General guidelines for their inclusion in standards
| 분야 | ISO/TC 61/SC 14 : Environmental aspects |
|---|---|
| 적용범위 | This document provides a structure for inclusion of environmental aspects in standards for plastics products. It proposes an approach which is directed at minimizing any adverse environmental impact without detracting from the primary purpose of ensuring adequate fitness for use of the products under consideration. The guidance provided by this document is intended primarily for use by standards writers. Over and above its primary purpose, however, this document provides guidance of value to those involved in design work and other activities where environmental aspects of plastics are being considered. NOTE This document is intended to promote the following practices: a) the use of techniques for identifying and assessing the environmental impact of technical provisions in standards, and for minimizing their adverse effects; b) the adoption of good practices such as: 1) procedures for pollution avoidance, e.g. through end-of-life options and its proper management; 2) material and energy conservation in the light of the intended use (and foreseeable misuse) of the product; 3) safe use of hazardous substances; 4) avoidance of technically unjustifiable restrictive practices; 5) promotion of performance criteria rather than exclusion clauses such as are based, for example, only on chemical composition criteria; 6) use of renewable resources and minimization of the use of non-renewable resources, if the life cycle assessment shows favourable; c) the adoption of a balanced approach in standards development to issues such as environmental impact, product function and performance, health and safety, and other regulatory requirements; d) the regular review and revision of existing standards in the light of technical innovations, permitting improvement in the environmental impact of products and processes; e) the application of life cycle analytical approaches wherever applicable and technically justifiable. |
| 국제분류(ICS)코드 |
83.080.01 : 플라스틱 일반
13.020.01 : 환경 및 환경 보호 일반 |
| 페이지수 | 12 |
| Edition | 2 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ISO 17422:2018 | Plastics — Environmental aspects — General guidelines for their inclusion in standards | 2018-07-10 | 표준 |
| 2 | ISO 17422:2002 | Plastics — Environmental aspects — General guidelines for their inclusion in standards | 2002-10-10 | 구판 |
관련상품이 존재하지 않습니다.
BS EN 15344:2021 - Plastics. Recycled plastics. Characterization of Polyethylene (PE) recyclates. 상세보기
ASTM D5203-07 - Standard Specification for Polyethylene Plastics Molding and Extrusion Materials from Recycled Post-Consumer (HDPE) Sources (Withdrawn 2016) 상세보기
ISO 15270:2008 - Plastics — Guidelines for the recovery and recycling of plastics waste 상세보기
ISO 22403:2020 - Plastics — Assessment of the intrinsic biodegradability of materials exposed to marine inocula under mesophilic aerobic laboratory conditions — Test methods and requirements 상세보기
NF EN 15343:2008 - Plastics - Recycled plastics - Plastics recycling traceability and assessment of conformity and recycled content 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
