관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
폐지
판매
Standard Specification for Polyethylene Plastics Molding and Extrusion Materials from Recycled Post-Consumer (HDPE) Sources (Withdrawn 2016)
| 분야 | 08.03 : 플라스틱 (Ⅲ) |
|---|---|
| 적용범위 | 1.1 This specification provides for the identification of recycled post-consumer HDPE molding and extrusion materials, from specified sources, in pellet or chip form so that the supplier and the user can agree on the acceptability of lots or shipments. This specification covers post-consumer HDPE materials from the following: (1) blow molded household chemical containers, (2) blow molded milk, juice, and water containers, (3) materials from the spunbonded process, (4) thermoformed packaged food containers and personal care packages, (5) injection molded packaged food containers and beverage bottle base cups, and (6) injection molded housewares and industrial articles such as pails, crates, totes, and pallets. Other post-consumer HDPE materials may be added to this specification when such material streams are characterized. 1.1.1 The tests described in this specification are intended to provide information for identifying these materials. The separation by sources improves the usefulness of the materials. 1.1.2 It is not the function of this specification to provide specific data for design purposes. 1.2 This specification provides a procedure to certify that the materials are from post-consumer sources. 1.3 The values stated in SI units are to be regarded as the standard. The inch-pound units given in parentheses are for information only. 1.4 The following precautionary caveat pertains only to the test method portion, Section 10, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Note 1There are no ISO standards covering the primary subject matter of this specification. |
| 국제분류(ICS)코드 | |
| 페이지수 | 4 |
| Edition | 07 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM D5203-07 | Standard Specification for Polyethylene Plastics Molding and Extrusion Materials from Recycled Post-Consumer (HDPE) Sources (Withdrawn 2016) | 2007-03-01 | 폐지 |
| 2 | ASTM D5203-02 | Standard Specification for Polyethylene Plastics Molding and Extrusion Materials from Recycled Post-Consumer (HDPE) Sources | 2002-11-10 | 구판 |
| 3 | ASTM D5203-98 | Standard Specification for Polyethylene Plastics Molding and Extrusion Materials from Recycled Post-Consumer (HDPE) Sources | 1998-04-10 | 구판 |
관련상품이 존재하지 않습니다.
BS EN 15344:2021 - Plastics. Recycled plastics. Characterization of Polyethylene (PE) recyclates. 상세보기
ISO 15270:2008 - Plastics — Guidelines for the recovery and recycling of plastics waste 상세보기
ISO 17422:2018 - Plastics — Environmental aspects — General guidelines for their inclusion in standards 상세보기
NF EN 15343:2008 - Plastics - Recycled plastics - Plastics recycling traceability and assessment of conformity and recycled content 상세보기
NF EN 15342:2008 - Plastics - Recycled plastics - Characterization of polystyrene (PS) recyclates 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
