관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
구판
판매
Non-destructive testing — Characterization and verification of ultrasonic phased array equipment — Part 3: Combined systems
| 분야 | ISO/TC 135/SC 3 : Ultrasonic testing |
|---|---|
| 적용범위 | ISO 18563-3:2015 addresses ultrasonic test systems implementing linear phased array probes, in contact (with or without wedge) or in immersion, with centre frequencies in the range of 0,5 MHz?10 MHz. It provides methods and acceptance criteria for verifying the performance of combined equipment (i.e. instrument, probe and cables connected). The methods described are suitable for users working under on-site or shop floor conditions. Its purpose is for the verification of the correct operation of the system prior to testing, and also the characterization of sound beams or verification of the absence of degradation of the system. The methods are not intended to prove the suitability of the system for particular applications, but are intended to prove the capability of the combined equipment to generate ultrasonic beams according to the settings used. The calibration of the system for a specific application is outside of the scope of part of ISO 18563 and it is intended that it be covered by the test procedure. ISO 18563-3:2015 does not address the following: - encircling arrays; - series of apertures having a different number of elements; - different settings for transmitting and receiving (e.g. active aperture, number of active elements, delays); - techniques using post-processing of the signals of individual elements in a more complex manner than a simple delay law (e.g. full matrix capture). |
| 국제분류(ICS)코드 | 19.100 : 비파괴 시험 및 기구 |
| 페이지수 | 34 |
| Edition | 1 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ISO 18563-3:2024 | Non-destructive testing — Characterization and verification of ultrasonic phased array equipment — Part 3: Complete systems | 2024-05-01 | 표준 |
| 2 | ISO 18563-3:2015 | Non-destructive testing — Characterization and verification of ultrasonic phased array equipment — Part 3: Combined systems | 2015-12-08 | 구판 |
ISO 18563-2 - Non-destructive testing — Characterization and verification of ultrasonic phased array equipment — Part 2: Array probes 상세보기
ISO 18563-2:2017 - Non-destructive testing — Characterization and verification of ultrasonic phased array equipment — Part 2: Probes 상세보기
ISO 18563-1:2022 - Non-destructive testing — Characterization and verification of ultrasonic phased array equipment — Part 1: Instruments 상세보기
ISO 18563-3:2024 - Non-destructive testing — Characterization and verification of ultrasonic phased array equipment — Part 3: Complete systems 상세보기
ISO 18563-1:2015 - Non-destructive testing — Characterization and verification of ultrasonic phased array equipment — Part 1: Instruments 상세보기
ISO 18563-2:2017 - Non-destructive testing — Characterization and verification of ultrasonic phased array equipment — Part 2: Probes 상세보기
ASTM E317-16 - Standard Practice for Evaluating Performance Characteristics of Ultrasonic Pulse-Echo Testing Instruments and Systems without the Use of Electronic Measurement Instruments 상세보기
ASTM E543-21 - Standard Specification for Agencies Performing Nondestructive Testing 상세보기
ASTM E317-21 - Standard Practice for Evaluating Performance Characteristics of Ultrasonic Pulse-Echo Testing Instruments and Systems without the Use of Electronic Measurement Instruments 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
