관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Non-destructive testing — Characterization and verification of ultrasonic phased array equipment — Part 3: Complete systems
| 분야 | ISO/TC 135/SC 3 : Ultrasonic testing |
|---|---|
| 적용범위 | This document addresses ultrasonic test systems implementing array probes, for contact technique (with or without wedge) or for immersion technique, with centre frequencies in the range of 0,5 MHz to 10 MHz. This document provides methods and acceptance criteria for determining the compliance of the complete system (see 3.2). Its purpose is for the verification of the correct operation of the system prior to testing or verification of the absence of degradation of the system. The methods are not intended to prove the suitability of the system for particular applications but are intended to prove the capability of the complete system (used for an application) to operate correctly according to the settings used. Tests can be performed on individual ultrasonic beams (for phased array technique, see 9.4.4) or on resulting images (for phased array technique and total focusing technique, see 9.4.3). The tests can be limited to the functions that are intended to be used for a certain application. This document does not cover the sensitivity setting of the system for a specific application. Nor does it apply to the characterization or verification of the mechanical scanning equipment. It is intended that these items will be covered by the test procedure. This document does not address the phased array technique using tandem technique. The characterization of beams, as recommended in case of dead elements or for more in-depth knowledge of the beams, is presented in Annex A. It is not applicable for signal processing technology using arrays. NOTE Unless stated otherwise, in this document ‘TFM’ and ‘TFM technique’ refer to the total focusing technique as defined in ISO 23243, and to related techniques, see for example ISO 23865 and ISO 23234. |
| 국제분류(ICS)코드 | 19.100 : 비파괴 시험 및 기구 |
| 페이지수 | 32 |
| Edition | 2 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ISO 18563-3:2024 | Non-destructive testing — Characterization and verification of ultrasonic phased array equipment — Part 3: Complete systems | 2024-05-01 | 표준 |
| 2 | ISO 18563-3:2015 | Non-destructive testing — Characterization and verification of ultrasonic phased array equipment — Part 3: Combined systems | 2015-12-08 | 구판 |
ISO 18563-2 - Non-destructive testing — Characterization and verification of ultrasonic phased array equipment — Part 2: Array probes 상세보기
ISO 18563-2:2017 - Non-destructive testing — Characterization and verification of ultrasonic phased array equipment — Part 2: Probes 상세보기
ISO 18563-1:2022 - Non-destructive testing — Characterization and verification of ultrasonic phased array equipment — Part 1: Instruments 상세보기
ISO 18563-1:2022 - Non-destructive testing — Characterization and verification of ultrasonic phased array equipment — Part 1: Instruments 상세보기
ISO 15548-2:2013 - Non-destructive testing — Equipment for eddy current examination — Part 2: Probe characteristics and verification 상세보기
ISO 15548-1:2013 - Non-destructive testing — Equipment for eddy current examination — Part 1: Instrument characteristics and verification 상세보기
ASTM E1065/E1065M-20 REDLINE - Standard Practice for Evaluating Characteristics of Ultrasonic Search Units 상세보기
ASTM E1065/E1065M-20 - Standard Practice for Evaluating Characteristics of Ultrasonic Search Units 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
