관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Calculation of load capacity of spur and helical gears — Part 1: Basic principles, introduction and general influence factors
| 분야 | ISO/TC 60/SC 2 : Gear capacity calculation |
|---|---|
| 적용범위 | This document presents the basic principles of, an introduction to, and the general influence factors for the calculation of the load capacity of spur and helical gears. Together with the other documents in the ISO 6336 series, it provides a method by which different gear designs can be compared. It is not intended to assure the performance of assembled drive gear systems. It is not intended for use by the general engineering public. Instead, it is intended for use by the experienced gear designer who is capable of selecting reasonable values for the factors in these formulae based on the knowledge of similar designs and the awareness of the effects of the items discussed. The formulae in the ISO 6336 series are intended to establish a uniformly acceptable method for calculating the load capacity of cylindrical gears with straight or helical involute teeth. The ISO 6336 series includes procedures based on testing and theoretical studies as referenced by each method. The methods are validated for: — normal working pressure angle from 15° to 25°; — reference helix angle up to 30°; — transverse contact ratio from 1,0 to 2,5. If this scope is exceeded, the calculated results will need to be confirmed by experience. The formulae in the ISO 6336 series are not applicable when any of the following conditions exist: — gears with transverse contact ratios less than 1,0; — interference between tooth tips and root fillets; — teeth are pointed; — backlash is zero. The rating formulae in the ISO 6336 series are not applicable to other types of gear tooth deterioration such as plastic deformation, case crushing and wear, and are not applicable under vibratory conditions where there can be an unpredictable profile breakdown. The ISO 6336 series does not apply to teeth finished by forging or sintering. It is not applicable to gears which have a poor contact pattern. The influence factors presented in these methods form a method to predict the risk of damage that aligns with industry and experimental experience. It is possible that they are not entirely scientifically exact. Therefore, the calculation methods from one part of the ISO 6336 series is not applicable in another part of the ISO 6336 series unless specifically referenced. The procedures in the ISO 6336 series provide rating formulae for the calculation of load capacity with regard to different failure modes such as pitting, tooth root breakage, tooth flank fracture, scuffing and micropitting. At pitch line velocities below 1 m/s the gear load capacity is often limited by abrasive wear (see other literature such as References [23] and [22] for further information on such calculation). |
| 국제분류(ICS)코드 | 21.200 : 기어류 |
| 페이지수 | 134 |
| Edition | 3 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ISO 6336-1:2019 | Calculation of load capacity of spur and helical gears — Part 1: Basic principles, introduction and general influence factors | 2019-11-27 | 표준 |
| 2 | ISO 6336-1:2006/Cor 1:2008 | 2008-05-26 | 구판 | |
| 3 | ISO 6336-1:2006 | Calculation of load capacity of spur and helical gears — Part 1: Basic principles, introduction and general influence factors | 2006-09-04 | 구판 |
| 4 | ISO 6336-1:1996/Cor 2:1999 | 1999-09-09 | 구판 | |
| 5 | ISO 6336-1:1996/Cor 1:1998 | 1998-10-15 | 구판 | |
| 6 | ISO 6336-1:1996 | Calculation of load capacity of spur and helical gears — Part 1: Basic principles, introduction and general influence factors | 1996-05-09 | 구판 |
ISO 6336-5:2016 - Calculation of load capacity of spur and helical gears — Part 5: Strength and quality of materials 상세보기
ISO/TS 6336-22:2018 - Calculation of load capacity of spur and helical gears — Part 22: Calculation of micropitting load capacity 상세보기
ISO/TR 6336-31:2018 - Calculation of load capacity of spur and helical gears — Part 31: Calculation examples of micropitting load capacity 상세보기
ISO/TS 6336-4:2019 - Calculation of load capacity of spur and helical gears — Part 4: Calculation of tooth flank fracture load capacity 상세보기
ISO 6336-2:2019 - Calculation of load capacity of spur and helical gears — Part 2: Calculation of surface durability (pitting) 상세보기
ISO 6336-2:2019 - Calculation of load capacity of spur and helical gears — Part 2: Calculation of surface durability (pitting) 상세보기
ISO 6336-3:2019 - Calculation of load capacity of spur and helical gears — Part 3: Calculation of tooth bending strength 상세보기
ISO 6336-5:2016 - Calculation of load capacity of spur and helical gears — Part 5: Strength and quality of materials 상세보기
ISO 6336-6:2019 - Calculation of load capacity of spur and helical gears — Part 6: Calculation of service life under variable load 상세보기
ISO/TS 6336-4:2019 - Calculation of load capacity of spur and helical gears — Part 4: Calculation of tooth flank fracture load capacity 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
