관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Calculation of load capacity of spur and helical gears — Part 3: Calculation of tooth bending strength
| 분야 | ISO/TC 60/SC 2 : Gear capacity calculation |
|---|---|
| 적용범위 | This document specifies the fundamental formulae for use in tooth bending stress calculations for involute external or internal spur and helical gears with a rim thickness sR > 0,5 ht for external gears and sR > 1,75 mn for internal gears. In service, internal gears can experience failure modes other than tooth bending fatigue, i.e. fractures starting at the root diameter and progressing radially outward. This document does not provide adequate safety against failure modes other than tooth bending fatigue. All load influences on the tooth root stress are included in so far as they are the result of loads transmitted by the gears and in so far as they can be evaluated quantitatively. This document includes procedures based on testing and theoretical studies such as those of Hirt[11], Strasser[14] and Brossmann[10]. The results are in good agreement with other methods (References [5], [6], [7] and [12]). The given formulae are valid for spur and helical gears with tooth profiles in accordance with the basic rack standardized in ISO 53. They can also be used for teeth conjugate to other basic racks if the virtual contact ratio εαn is less than 2,5. The load capacity determined on the basis of permissible bending stress is termed "tooth bending strength". The results are in good agreement with other methods for the range, as indicated in the scope of ISO 6336‑1. If this scope does not apply, refer to ISO 6336-1:2019, Clause 4. |
| 국제분류(ICS)코드 | 21.200 : 기어류 |
| 페이지수 | 55 |
| Edition | 3 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ISO 6336-3:2019 | Calculation of load capacity of spur and helical gears — Part 3: Calculation of tooth bending strength | 2019-11-26 | 표준 |
| 2 | ISO 6336-3:2006/Cor 1:2008 | 2008-05-26 | 구판 | |
| 3 | ISO 6336-3:2006 | Calculation of load capacity of spur and helical gears — Part 3: Calculation of tooth bending strength | 2006-09-04 | 구판 |
| 4 | ISO 6336-3:1996/Cor 1:1999 | 1999-09-09 | 구판 | |
| 5 | ISO 6336-3:1996 | Calculation of load capacity of spur and helical gears — Part 3: Calculation of tooth bending strength | 1996-06-13 | 구판 |
ISO 6336-5:2016 - Calculation of load capacity of spur and helical gears — Part 5: Strength and quality of materials 상세보기
ISO/TS 6336-22:2018 - Calculation of load capacity of spur and helical gears — Part 22: Calculation of micropitting load capacity 상세보기
ISO/TR 6336-31:2018 - Calculation of load capacity of spur and helical gears — Part 31: Calculation examples of micropitting load capacity 상세보기
ISO/TS 6336-4:2019 - Calculation of load capacity of spur and helical gears — Part 4: Calculation of tooth flank fracture load capacity 상세보기
ISO 6336-2:2019 - Calculation of load capacity of spur and helical gears — Part 2: Calculation of surface durability (pitting) 상세보기
ISO 6336-2:2019 - Calculation of load capacity of spur and helical gears — Part 2: Calculation of surface durability (pitting) 상세보기
ISO 6336-1:2019 - Calculation of load capacity of spur and helical gears — Part 1: Basic principles, introduction and general influence factors 상세보기
ISO 6336-5:2016 - Calculation of load capacity of spur and helical gears — Part 5: Strength and quality of materials 상세보기
ISO 6336-6:2019 - Calculation of load capacity of spur and helical gears — Part 6: Calculation of service life under variable load 상세보기
ISO/TS 6336-4:2019 - Calculation of load capacity of spur and helical gears — Part 4: Calculation of tooth flank fracture load capacity 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
