관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
구판
판매
Determination of flash point — Pensky-Martens closed cup method
| 분야 | ISO/TC 28 : Petroleum and related products, fuels and lubricants from natural or synthetic sources |
|---|---|
| 적용범위 | ISO 2719:2002 describes two procedures, A and B, using the Pensky-Martens closed cup tester, for determining the flash point of combustible liquids, liquids with suspended solids, liquids that tend to form a surface film under the test conditions and other liquids. It is applicable for liquids with a flash point above 40 degrees C. Procedure A is used for the determination of the flash point of paints and varnishes that do not form a surface film, unused lubricating oils and other petroleum products not covered by Procedure B. Procedure B is used for the determination of the flash point of residual fuel oils, cutback bitumens, used lubricating oils, liquids that tend to form a surface film, liquids with suspensions of solids and highly viscous materials such as polymeric solutions and adhesives. ISO 2719:2002 is not applicable to water-borne paints or liquids contaminated by traces of highly volatile materials. |
| 국제분류(ICS)코드 | 75.080 : 석유제품 일반 |
| 페이지수 | 21 |
| Edition | 3 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ISO 2719:2016/Amd 1:2021 | Determination of flash point — Pensky-Martens closed cup method — Amendment 1: Thermometers correction | 2021-03-15 | 표준 |
| 2 | ISO 2719:2016 | Determination of flash point — Pensky-Martens closed cup method | 2016-06-16 | 표준 |
| 3 | ISO 2719:2002 | Determination of flash point — Pensky-Martens closed cup method | 2002-11-15 | 구판 |
| 4 | ISO 2719:1988 | Petroleum products and lubricants -- Determination of flash point -- Pensky-Martens closed cup method | 1988-12-15 | 구판 |
| 5 | ISO 2719:1973 | Petroleum products -- Determination of flash point -- Pensky-Martens closed cup method | 1973-09-01 | 구판 |
| 6 | ISO/DIS 2719 | Determination of flash point — Pensky-Martens closed cup method | 초안 |
관련상품이 존재하지 않습니다.
IEEE C57.12.20-2011 - IEEE Standard for Overhead-Type Distribution Transformers 500 kVA and Smaller: High Voltage, 34 500 V and Below; Low Voltage, 7970/13 800Y V and Below 상세보기
IEEE C57.12.00-2010 - IEEE Standard for General Requirements for Liquid-Immersed Distribution, Power, and Regulating Transformers 상세보기
ASTM D3359-02 - Standard Test Methods for Measuring Adhesion by Tape Test 상세보기
ASTM D1654-05 - Standard Test Method for Evaluation of Painted or Coated Specimens Subjected to Corrosive Environments 상세보기
ASTM D4060-07 - Standard Test Method for Abrasion Resistance of Organic Coatings by the Taber Abraser 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
