관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
구판
판매
Standard Test Methods for Measuring Adhesion by Tape Test
| 분야 | 06.01 : 페인트-화학적, 물리적, 광학적특성 시험; 현상 |
|---|---|
| 적용범위 | 1.1 These test methods cover procedures for assessing the adhesion of coating films to metallic substrates by applying and removing pressure-sensitive tape over cuts made in the film. 1.2 Test Method A is primarily intended for use at job sites while Test Method B is more suitable for use in the laboratory. Also, Test Method B is not considered suitable for films thicker than 5 mils (125μm). Note 1—Subject to agreement between the purchaser and the seller, Test Method B can be used for thicker films if wider spaced cuts are employed. 1.3 These test methods are used to establish whether the adhesion of a coating to a substrate is at a generally adequate level. They do not distinguish between higher levels of adhesion for which more sophisticated methods of measurement are required. Note 2—It should be recognized that differences in adherability of the coating surface can affect the results obtained with coatings having the same inherent adhesion. 1.4 In multicoat systems adhesion failure may occur between coats so that the adhesion of the coating system to the substrate is not determined. 1.5 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.6 This standard does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
| 국제분류(ICS)코드 | |
| 페이지수 | 7 |
| Edition | 02 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM D3359-23 | Standard Test Methods for Rating Adhesion by Tape Test | 2023-02-01 | 표준 |
| 2 | ASTM D3359-23 REDLINE | Standard Test Methods for Rating Adhesion by Tape Test | 2023-02-01 | 표준 |
| 3 | ASTM D3359-22 | Standard Test Methods for Rating Adhesion by Tape Test | 2022-07-01 | 구판 |
| 4 | ASTM D3359-22 REDLINE | Standard Test Methods for Rating Adhesion by Tape Test | 2022-07-01 | 구판 |
| 5 | ASTM D3359-17 | Standard Test Methods for Rating Adhesion by Tape Test | 2017-02-01 | 구판 |
| 6 | ASTM D3359-17 REDLINE | Standard Test Methods for Rating Adhesion by Tape Test | 2017-02-01 | 구판 |
| 7 | ASTM D3359-09e2 | Standard Test Methods for Measuring Adhesion by Tape Test | 2009-06-01 | 구판 |
| 8 | ASTM D3359-09e1 | Standard Test Methods for Measuring Adhesion by Tape Test | 2009-06-01 | 구판 |
| 9 | ASTM D3359-09 | Standard Test Methods for Measuring Adhesion by Tape Test | 2009-06-01 | 구판 |
| 10 | ASTM D3359-08 | Standard Test Methods for Measuring Adhesion by Tape Test | 2008-02-01 | 구판 |
| 11 | ASTM D3359-07 | Standard Test Methods for Measuring Adhesion by Tape Test | 2007-11-01 | 구판 |
| 12 | ASTM D3359-02 | Standard Test Methods for Measuring Adhesion by Tape Test | 2002-08-10 | 구판 |
| 13 | ASTM D3359-97 | Standard Test Methods for Measuring Adhesion by Tape Test | 1997-11-10 | 구판 |
관련상품이 존재하지 않습니다.
IEEE C57.12.20-2011 - IEEE Standard for Overhead-Type Distribution Transformers 500 kVA and Smaller: High Voltage, 34 500 V and Below; Low Voltage, 7970/13 800Y V and Below 상세보기
IEEE C57.12.00-2010 - IEEE Standard for General Requirements for Liquid-Immersed Distribution, Power, and Regulating Transformers 상세보기
ASTM D1654-05 - Standard Test Method for Evaluation of Painted or Coated Specimens Subjected to Corrosive Environments 상세보기
ASTM D4060-07 - Standard Test Method for Abrasion Resistance of Organic Coatings by the Taber Abraser 상세보기
ISO 2592:2000 - Determination of flash and fire points — Cleveland open cup method 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
