관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
구판
판매
Standard Test Methods for Rating Adhesion by Tape Test
| 분야 | |
|---|---|
| 적용범위 | 1.1?These test methods cover procedures for assessing the adhesion of relatively ductile coating films to metallic substrates by applying and removing pressure-sensitive tape over cuts made in the film. 1.2?Test Method A is primarily intended for use in the field while Test Method B is more suitable for use in laboratory or shop environments. Also, Test Method B is not considered suitable for films thicker than 125?μm (5 mils) unless wider spaced cuts are employed and there is an explicit agreement between the purchaser and seller. 1.3?These test methods are used to evaluate whether the adhesion of a coating to a substrate is adequate for the user’s application. They do not distinguish between higher levels of adhesion for which more sophisticated methods of measurement are required. 1.4?This test method is similar in content (but not technically equivalent) to ISO 2409. 1.5?In multicoat systems adhesion failure may occur between coats so that the adhesion of the coating system to the substrate is not determined. 1.6?The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.7?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | |
| 페이지수 | 8 |
| Edition | 22 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM D3359-23 | Standard Test Methods for Rating Adhesion by Tape Test | 2023-02-01 | 표준 |
| 2 | ASTM D3359-23 REDLINE | Standard Test Methods for Rating Adhesion by Tape Test | 2023-02-01 | 표준 |
| 3 | ASTM D3359-22 | Standard Test Methods for Rating Adhesion by Tape Test | 2022-07-01 | 구판 |
| 4 | ASTM D3359-22 REDLINE | Standard Test Methods for Rating Adhesion by Tape Test | 2022-07-01 | 구판 |
| 5 | ASTM D3359-17 | Standard Test Methods for Rating Adhesion by Tape Test | 2017-02-01 | 구판 |
| 6 | ASTM D3359-17 REDLINE | Standard Test Methods for Rating Adhesion by Tape Test | 2017-02-01 | 구판 |
| 7 | ASTM D3359-09e2 | Standard Test Methods for Measuring Adhesion by Tape Test | 2009-06-01 | 구판 |
| 8 | ASTM D3359-09e1 | Standard Test Methods for Measuring Adhesion by Tape Test | 2009-06-01 | 구판 |
| 9 | ASTM D3359-09 | Standard Test Methods for Measuring Adhesion by Tape Test | 2009-06-01 | 구판 |
| 10 | ASTM D3359-08 | Standard Test Methods for Measuring Adhesion by Tape Test | 2008-02-01 | 구판 |
| 11 | ASTM D3359-07 | Standard Test Methods for Measuring Adhesion by Tape Test | 2007-11-01 | 구판 |
| 12 | ASTM D3359-02 | Standard Test Methods for Measuring Adhesion by Tape Test | 2002-08-10 | 구판 |
| 13 | ASTM D3359-97 | Standard Test Methods for Measuring Adhesion by Tape Test | 1997-11-10 | 구판 |
관련상품이 존재하지 않습니다.
SAE AMS2750G - Pyrometry 상세보기
ASTM D3363-22 REDLINE - Standard Test Method for Film Hardness by Pencil Test 상세보기
ASTM D7091-22 REDLINE - Standard Practice for Nondestructive Measurement of Dry Film Thickness of Nonmagnetic Coatings Applied to Ferrous Metals and Nonmagnetic, Nonconductive Coatings Applied to Non-Ferrous Metals 상세보기
ASTM E18-22 REDLINE - Standard Test Methods for Rockwell Hardness of Metallic Materials 상세보기
ASTM B733-22 REDLINE - Standard Specification for Autocatalytic (Electroless) Nickel-Phosphorus Coatings on Metal 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
