관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Fuel Cell Power Systems Performance (PTC 50 - 2002)
| 분야 | PTC : Performance Test Code |
|---|---|
| 적용범위 | This Code provides test procedures, methods and definitions for the performance characterization of fuel cell power systems. Fuel cell power systems include all components required in the conversion of input fuel and oxidizer into output electrical and thermal energy. Performance characterization of fuel systems includes evaluating system energy inputs and electrical and thermal outputs to determine fuel-to-electrical energy conversion efficiency and where applicable the overall thermal effectiveness. These efficiencies will be determined to an absolute uncertainty of less than A± 2% at a 95% confidence level. (For example, for a calculated efficiency of 40%, the true value lies between 38% and 42%.) This Code applies to all fuel cell power systems regardless of the electrical power output, thermal output, fuel cell type, fuel type, or system application. Fuel cell power systems contain an assembly of electrochemical cells, which oxidize a fuel to generate direct current electricity. Balance-of- plant subsystems may include controls, thermal management, a fuel processor and a power conditioner. Some fuel cell power systems may contain additional power generating equipment such as steam generators, gas turbine generators, or micro-turbine generators. The net power output and all the fuel input to the system shall be taken into account in the performance test calculations. This Code applies to the performance of overall fuel cell power systems. The Code addresses combined heat and power systems, that is, the generation of electricity and usable heat at specific thermal conditions. It does not address the performance of specific subsystems nor does it apply to energy storage systems, such as regenerative fuel cells or batteries. It also does not address emissions, reliability, safety issues, or endurance. This Code contains methods and procedures for conducting and reporting fuel cell system testing, including instrumentation to be used, testing techniques, and methods for calculating and reporting results. The Code defines the test boundary for fuel and oxidant input, secondary energy input and net electrical and thermal energy output. At these boundaries, this Code provides procedures for measuring temperature, pressure, input fuel flow and composition, electrical power, and thermal output. The Code provides procedures for determination of electrical efficiency or heat rate and overall thermal effectiveness at rated or any other steady state condition. The Code also provides the method to correct results from the test to reference conditions. |
| 국제분류(ICS)코드 | |
| 페이지수 | 48 |
| Edition |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASME PTC 50-2002(R2014) | Fuel Cell Power Systems Performance (PTC 50 - 2002) | 2002-01-01 | 구판 |
| 2 | ASME PTC 50-2002(R2019) | Fuel Cell Power Systems Performance (PTC 50 - 2002) | 2002-01-01 | 표준 |
관련상품이 존재하지 않습니다.
ASME B31.12-2019 - Hydrogen Piping and Pipelines (B31.12 - 2014) 상세보기
SAE J2615_201110 - Testing Performance of Fuel Cell Systems for Automotive Applications (Stabilized: Oct 2011) 상세보기
GOST R 70557-2022 - Ship electric power systems based on fuel cells. Fuel cell stacks. General technical requirements 상세보기
AS ISO 16110.2:2020 - Hydrogen generators using fuel processing technologies, Part 2: Test methods for performance 상세보기
ASME PTC 18-2020 - Hydraulic Turbines and Pump-Turbines (PTC 18 - 2020) 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
