관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
구판
판매
Standard Test Method for Seal Strength of Flexible Barrier Materials
| 분야 | |
|---|---|
| 적용범위 | 1.1?This test method covers the measurement of the strength of seals in flexible barrier materials. 1.2?The test may be conducted on seals between a flexible material and a rigid material. 1.3?Seals tested in accordance with this test method may be from any source, laboratory or commercial. 1.4?This test method measures the force required to separate a test strip of material containing the seal. It also identifies the mode of specimen failure. 1.5?This test method differs from Test Method F2824. Test Method F2824 measures mechanical seal strength while separating an entire lid (cover/membrane) from a rigid or semi-rigid round container. 1.6?This test method differs from Test Method F904. Test Method F904 measures the bond strength or ply adhesion of laminates made from flexible materials such as cellulose, paper, plastic film, and foil. 1.7?The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.8?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.9?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | |
| 페이지수 | 11 |
| Edition | 21 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM F88/F88M-23 | Standard Test Method for Seal Strength of Flexible Barrier Materials | 2023-05-01 | 표준 |
| 2 | ASTM F88/F88M-23 REDLINE | Standard Test Method for Seal Strength of Flexible Barrier Materials | 2023-05-01 | 표준 |
| 3 | ASTM F88/F88M-21 | Standard Test Method for Seal Strength of Flexible Barrier Materials | 2021-11-15 | 구판 |
| 4 | ASTM F88/F88M-21 REDLINE | Standard Test Method for Seal Strength of Flexible Barrier Materials | 2021-11-15 | 구판 |
| 5 | ASTM F88/F88M-15 REDLINE | Standard Test Method for Seal Strength of Flexible Barrier Materials | 2015-11-01 | 구판 |
| 6 | ASTM F88/F88M-15 | Standard Test Method for Seal Strength of Flexible Barrier Materials | 2015-11-01 | 구판 |
| 7 | ASTM F88/F88M-09 | Standard Test Method for Seal Strength of Flexible Barrier Materials | 2009-06-15 | 구판 |
관련상품이 존재하지 않습니다.
ASTM F2182-19e2 - Standard Test Method for Measurement of Radio Frequency Induced Heating On or Near Passive Implants During Magnetic Resonance Imaging 상세보기
ASTM F2213-17 - Standard Test Method for Measurement of Magnetically Induced Torque on Medical Devices in the Magnetic Resonance Environment 상세보기
ASTM F1886/F1886M-16 - Standard Test Method for Determining Integrity of Seals for Flexible Packaging by Visual Inspection 상세보기
ASTM F2052-14 - Standard Test Method for Measurement of Magnetically Induced Displacement Force on Medical Devices in the Magnetic Resonance Environment 상세보기
ASTM F2182-11a - Standard Test Method for Measurement of Radio Frequency Induced Heating On or Near Passive Implants During Magnetic Resonance Imaging 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
