관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Standard Test Method for Tensile Properties of Thin Plastic Sheeting
| 분야 | |
|---|---|
| 적용범위 | 1.1 This test method covers the determination of tensile properties of plastics in the form of thin sheeting and films (less than 1.0 mm (0.04 in.) in thickness). Note 1: Film is defined in Terminology D883 as an optional term for sheeting having a nominal thickness no greater than 0.25 mm (0.010 in.). Note 2: Tensile properties of plastics 1.0 mm (0.04 in.) or greater in thickness shall be determined according to Test Method D638. 1.2 This test method can be used to test all plastics within the thickness range described and the capacity of the machine employed. 1.3 Specimen extension can be measured by grip separation, extension indicators, or displacement of gage marks. 1.4 The procedure for determining the tensile modulus of elasticity is included at one strain rate. Note 3: The modulus determination is generally based on the use of grip separation as a measure of extension; however, the desirability of using extensometers, as described in 6.2, is recognized and provision for the use of such instrumentation is incorporated in the procedure. 1.5 Test data obtained by this test method is relevant and appropriate for use in engineering design. 1.6 The values stated in SI units are to be regarded as the standard. The values in parentheses are provided for information only. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Note 4: This test method is similar to ISO 527-3, but is not considered technically equivalent. ISO 527-3 allows for additional specimen configurations, specifies different test speeds, and requires an extensometer or gage marks on the specimen. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | |
| 페이지수 | 12 |
| Edition | 18 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM D882-18 REDLINE | Standard Test Method for Tensile Properties of Thin Plastic Sheeting | 2018-08-01 | 표준 |
| 2 | ASTM D882-18 | Standard Test Method for Tensile Properties of Thin Plastic Sheeting | 2018-08-01 | 표준 |
| 3 | ASTM D882-12 | Standard Test Method for Tensile Properties of Thin Plastic Sheeting | 2012-08-01 | 구판 |
| 4 | ASTM D882-10 | Standard Test Method for Tensile Properties of Thin Plastic Sheeting | 2010-04-01 | 구판 |
| 5 | ASTM D882-09 | Standard Test Method for Tensile Properties of Thin Plastic Sheeting | 2009-01-01 | 구판 |
| 6 | ASTM D882-00 | Standard Test Method for Tensile Properties of Thin Plastic Sheeting | 2002-04-10 | 구판 |
| 7 | ASTM D882-01 | Standard Test Method for Tensile Properties of Thin Plastic Sheeting | 2002-04-10 | 구판 |
| 8 | ASTM D882-02 | Standard Test Method for Tensile Properties of Thin Plastic Sheeting | 2002-04-10 | 구판 |
| 9 | ASTM D882-97 | Standard Test Method for Tensile Properties of Thin Plastic Sheeting | 구판 |
관련상품이 존재하지 않습니다.
ASTM F1983-14 REDLINE - Standard Practice for Assessment of Selected Tissue Effects of Absorbable Biomaterials for Implant Applications 상세보기
ASTM F2212-20 REDLINE - Standard Guide for Characterization of Type I Collagen as Starting Material for Surgical Implants and Substrates for Tissue Engineered Medical Products (TEMPs) 상세보기
ISO 21534:2007 - Non-active surgical implants — Joint replacement implants — Particular requirements 상세보기
ISO 10993-6:2016 - Biological evaluation of medical devices — Part 6: Tests for local effects after implantation 상세보기
ISO 14630:2012 - Non-active surgical implants — General requirements 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
