관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Standard Practice for Fabrication and Control of Flat Bottomed Hole Ultrasonic Standard Reference Blocks
| 분야 | 03.03 : 비 파괴검사 (Ⅰ) |
|---|---|
| 적용범위 | 1.1?This practice covers a procedure for fabrication and control of metal alloy reference blocks used in ultrasonic examinations that contain flat bottom holes (FBH). 1.2?These blocks may be used for checking the performance of ultrasonic examination instrumentation and search units and for standardization and control of ultrasonic examination of metal alloy products. 1.3?The reference blocks described are suitable for use with either the direct-contact method or immersion pulse-echo ultrasonic methods. 1.4?Standard sets are described for flat surface sound entry; the Basic set, Area-Amplitude set, and Distance Amplitude set. 1.5?The requirements for FBH fabrication may be applied to round bar/billet reference standards and reference standards fabricated from other product forms. 1.6?This practice does not specify reference reflector sizes or product rejection limits. It does describe fabrication practices and applied tolerances. In all cases of conflict between this practice and customer specifications, the customer specification shall prevail. 1.7?The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.8?This practice has incorporated the requirements of Practice E428 and Guide E1158. Reference standards that were manufactured under Practice E428 and Guide E1158 comply with the requirements of this practice. 1.9?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.10?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 |
77.040.01 : 금속시험 일반
77.120.10 : 알루미늄 및 알루미늄합금 |
| 페이지수 | 16 |
| Edition | 20 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM E127-20 | Standard Practice for Fabrication and Control of Flat Bottomed Hole Ultrasonic Standard Reference Blocks | 2020-12-01 | 표준 |
| 2 | ASTM E127-20 REDLINE | Standard Practice for Fabrication and Control of Flat Bottomed Hole Ultrasonic Standard Reference Blocks | 2020-12-01 | 표준 |
| 3 | ASTM E127-19e1 | Standard Practice for Fabrication and Control of Flat Bottomed Hole Ultrasonic Standard Reference Blocks | 2019-07-15 | 구판 |
| 4 | ASTM E127-19 | Standard Practice for Fabrication and Control of Flat Bottomed Hole Ultrasonic Standard Reference Blocks | 2019-07-15 | 구판 |
| 5 | ASTM E127-19 REDLINE | Standard Practice for Fabrication and Control of Flat Bottomed Hole Ultrasonic Standard Reference Blocks | 2019-07-15 | 구판 |
| 6 | ASTM E127-15 REDLINE | Standard Practice for Fabrication and Control of Aluminum Alloy Ultrasonic Standard Reference Blocks | 2015-06-01 | 구판 |
| 7 | ASTM E127-15 | Standard Practice for Fabrication and Control of Aluminum Alloy Ultrasonic Standard Reference Blocks | 2015-06-01 | 구판 |
| 8 | ASTM E127-10 | Standard Practice for Fabricating and Checking Aluminum Alloy Ultrasonic Standard Reference Blocks | 2010-02-15 | 구판 |
| 9 | ASTM E127-07 | Standard Practice for Fabricating and Checking Aluminum Alloy Ultrasonic Standard Reference Blocks | 2007-12-01 | 구판 |
| 10 | ASTM E127-06 | Standard Practice for Fabricating and Checking Aluminum Alloy Ultrasonic Standard Reference Blocks | 2006-05-01 | 구판 |
| 11 | ASTM E127-05 | Standard Practice for Fabricating and Checking Aluminum Alloy Ultrasonic Standard Reference Blocks | 2005-04-01 | 구판 |
| 12 | ASTM E127-04 | Standard Practice for Fabricating and Checking Aluminum Alloy Ultrasonic Standard Reference Blocks | 2004-07-01 | 구판 |
| 13 | ASTM E127-98 | Standard Practice for Fabricating and Checking Aluminum Alloy Ultrasonic Standard Reference Blocks | 1998-12-10 | 구판 |
관련상품이 존재하지 않습니다.
ASTM A36/A36M-19 - Standard Specification for Carbon Structural Steel 상세보기
ASTM B594-19 - Standard Practice for Ultrasonic Inspection of Aluminum-Alloy Wrought Products 상세보기
ASTM E317-16 - Standard Practice for Evaluating Performance Characteristics of Ultrasonic Pulse-Echo Testing Instruments and Systems without the Use of Electronic Measurement Instruments 상세보기
ASTM E1158-14 - Standard Guide for Material Selection and Fabrication of Reference Blocks for the Pulsed Longitudinal Wave Ultrasonic Testing of Metal and Metal Alloy Production Material (Withdrawn 2019) 상세보기
ASTM B107/B107M-13 - Standard Specification for Magnesium-Alloy Extruded Bars, Rods, Profiles, Tubes, and Wire 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
