관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Standard Test Methods for Pitting and Crevice Corrosion Resistance of Stainless Steels and Related Alloys by Use of Ferric Chloride Solution
| 분야 | 03.02 : 마모 및 침식;금속 부식 |
|---|---|
| 적용범위 | 1.1?These test methods cover procedures for the determination of the resistance of stainless steels and related alloys to pitting and crevice corrosion (see Terminology G193) when exposed to oxidizing chloride environments. Six procedures are described and identified as Methods A, B, C, D, E, and F. 1.1.1?Method A?Ferric chloride pitting test. 1.1.2?Method B?Ferric chloride crevice test. 1.1.3?Method C?Critical pitting temperature test for nickel-base and chromium-bearing alloys. 1.1.4?Method D?Critical crevice temperature test for nickel-base and chromium-bearing alloys. 1.1.5?Method E?Critical pitting temperature test for stainless steels. 1.1.6?Method F?Critical crevice temperature test for stainless steels. 1.2?Method A is designed to determine the relative pitting resistance of stainless steels and nickel-base, chromium-bearing alloys, whereas Method B can be used for determining both the pitting and crevice corrosion resistance of these alloys. Methods C, D, E, and F allow for a ranking of alloys by minimum (critical) temperature to cause initiation of pitting corrosion and crevice corrosion, respectively, of stainless steels, nickel-base and chromium-bearing alloys in a standard ferric chloride solution. 1.3?These tests may be used to determine the effects of alloying additives, heat treatment, and surface finishes on pitting and crevice corrosion resistance. 1.4?The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard. 1.5?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | 77.060 : 금속 부식 |
| 페이지수 | 11 |
| Edition | 11(2020)e1 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM G48-11(2020)e1 | Standard Test Methods for Pitting and Crevice Corrosion Resistance of Stainless Steels and Related Alloys by Use of Ferric Chloride Solution | 2020-11-01 | 표준 |
| 2 | ASTM G48-11(2015) | Standard Test Methods for Pitting and Crevice Corrosion Resistance of Stainless Steels and Related Alloys by Use of Ferric Chloride Solution | 2015-11-01 | 구판 |
| 3 | ASTM G48-11 | : Standard Test Methods for Pitting and Crevice Corrosion Resistance of Stainless Steels and Related Alloys by Use of Ferric Chloride Solution | 2011-09-01 | 구판 |
| 4 | ASTM G48-03(2009) | Standard Test Methods for Pitting and Crevice Corrosion Resistance of Stainless Steels and Related Alloys by Use of Ferric Chloride Solution | 2003-05-10 | 구판 |
| 5 | ASTM G48-03 | Standard Test Methods for Pitting and Crevice Corrosion Resistance of Stainless Steels and Related Alloys by Use of Ferric Chloride Solution | 2003-05-10 | 구판 |
| 6 | ASTM G48-99A | Standard Test Methods for Pitting and Crevice Corrosion Resistance of Stainless Steels and Related Alloys by Use of Ferric Chloride Solution | 2000-05-10 | 구판 |
| 7 | ASTM G48-00 | Standard Test Methods for Pitting and Crevice Corrosion Resistance of Stainless Steels and Related Alloys by Use of Ferric Chloride Solution | 2000-05-10 | 구판 |
관련상품이 존재하지 않습니다.
ASTM E562-19e1 - Standard Test Method for Determining Volume Fraction by Systematic Manual Point Count 상세보기
ASTM A262-15(2021) - Standard Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels 상세보기
ISO 6892-1:2019 - Metallic materials — Tensile testing — Part 1: Method of test at room temperature 상세보기
ASTM A530/A530M-18 - Standard Specification for General Requirements for Specialized Carbon and Alloy Steel Pipe 상세보기
ASTM E21-20 - Standard Test Methods for Elevated Temperature Tension Tests of Metallic Materials 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
