관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Standard Specification for General Requirements for Specialized Carbon and Alloy Steel Pipe
| 분야 | |||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 적용범위 | 1.1 This specification2 covers a group of requirements which, with the exceptions of Section 6.3, Section 14, Section 21, and Section 22, are mandatory requirements to the ASTM pipe product specifications noted below unless the product specification specifies different requirements, in which case the requirement of the product specification shall prevail. 1.2 Sections 6.3 or 21 are mandatory if the product specification has a requirement for product analysis or flattening tests. 1.3 Section 22 is mandatory if the product specification has a hydrostatic test requirement without defining the test parameters. 1.4 Section 14 is for information only. 1.5 In case of conflict between a requirement of the product specification and a requirement of this general requirement specification, only the requirement of the product specification need be satisfied.
1.6 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. The inch-pound units shall apply unless the “M” designation (SI) of the product specification is specified in the order. Note 1: The dimensionless designator NPS (nominal pipe size) has been substituted in this standard for such traditional terms as “nominal diameter,” “size,” and “nominal size.” 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||||||||
| 국제분류(ICS)코드 | 23.040.10 : 주철 및 강 파이프 | ||||||||||||||||
| 페이지수 | 9 | ||||||||||||||||
| Edition | 18 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM A530/A530M-18 REDLINE | Standard Specification for General Requirements for Specialized Carbon and Alloy Steel Pipe | 2018-09-01 | 표준 |
| 2 | ASTM A530/A530M-18 | Standard Specification for General Requirements for Specialized Carbon and Alloy Steel Pipe | 2018-09-01 | 표준 |
| 3 | ASTM A530/A530M-12 | Standard Specification for General Requirements for Specialized Carbon and Alloy Steel Pipe | 2012-05-01 | 구판 |
| 4 | ASTM A530/A530M-04a(2010) | Standard Specification for General Requirements for Specialized Carbon and Alloy Steel Pipe | 2010-04-01 | 구판 |
| 5 | ASTM A530/A530M-04a | Standard Specification for General Requirements for Specialized Carbon and Alloy Steel Pipe | 2004-10-01 | 구판 |
| 6 | ASTM A530/A530M-04 | Standard Specification for General Requirements for Specialized Carbon and Alloy Steel Pipe | 2004-03-01 | 구판 |
| 7 | ASTM A530/A530M-03 | Standard Specification for General Requirements for Specialized Carbon and Alloy Steel Pipe | 2003-09-10 | 구판 |
| 8 | ASTM A530/A530M-02 | Standard Specification for General Requirements for Specialized Carbon and Alloy Steel Pipe | 2002-09-10 | 구판 |
| 9 | ASTM A530/A530M-99e1 | Standard Specification for General Requirements for Specialized Carbon and Alloy Steel Pipe | 1999-09-10 | 구판 |
관련상품이 존재하지 않습니다.
ASTM A370-20 - Standard Test Methods and Definitions for Mechanical Testing of Steel Products 상세보기
ASTM A999/A999M-18 - Standard Specification for General Requirements for Alloy and Stainless Steel Pipe 상세보기
ASTM A1016/A1016M-18a - Standard Specification for General Requirements for Ferritic Alloy Steel, Austenitic Alloy Steel, and Stainless Steel Tubes 상세보기
ASTM E23-18 - Standard Test Methods for Notched Bar Impact Testing of Metallic Materials 상세보기
ASTM A358/A358M-19 - Standard Specification for Electric-Fusion-Welded Austenitic Chromium-Nickel Stainless Steel Pipe for High-Temperature Service and General Applications 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
