관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Standard Specification for Hex Cap Screws, Bolts and Studs, Steel, Heat Treated, 120/105/90 ksi Minimum Tensile Strength, General Use
| 분야 | 01.09 : 비철화스너 (구름요소베어링) | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| 적용범위 | 1.1?This specification2 covers quenched and tempered steel hex cap screws, bolts, and studs having a minimum tensile strength of 120 ksi for diameters 1.0 in. and smaller; 105 ksi for diameters over 1.0 in. to 11/2?in.; and 90 ksi for diameters 13/4?in. to 3.0 in. inclusive. The term "fasteners" in this specification denotes hex cap screws, bolts, and studs. 1.2?The fasteners are intended for general engineering use. 1.3?The fasteners are furnished in diameters 1/4?to 3.0 in. inclusive. They are designated by type denoting chemical composition as follows:
1.4?Terms used in this specification are defined in Terminology F1789 unless otherwise defined in this specification. 1.5?The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard. 1.6?This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7?This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||||
| 국제분류(ICS)코드 | 21.060.10 : 볼트. 나사. 스터드 | ||||||||||
| 페이지수 | 7 | ||||||||||
| Edition | 14(2020) |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM A449-14(2020) | Standard Specification for Hex Cap Screws, Bolts and Studs, Steel, Heat Treated, 120/105/90 ksi Minimum Tensile Strength, General Use | 2020-12-01 | 표준 |
| 2 | ASTM A449-14 | Standard Specification for Hex Cap Screws, Bolts and Studs, Steel, Heat Treated, 120/105/90 ksi Minimum Tensile Strength, General Use | 2014-10-01 | 구판 |
| 3 | ASTM A449-14 REDLINE | Standard Specification for Hex Cap Screws, Bolts and Studs, Steel, Heat Treated, 120/105/90 ksi Minimum Tensile Strength, General Use | 2014-10-01 | 구판 |
| 4 | ASTM A449-10 | Standard Specification for Hex Cap Screws, Bolts and Studs, Steel, Heat Treated, 120/105/90 ksi Minimum Tensile Strength, General Use | 2010-10-01 | 구판 |
| 5 | ASTM A449-07be1 | Standard Specification for Hex Cap Screws, Bolts and Studs, Steel, Heat Treated, 120/105/90 ksi Minimum Tensile Strength, General Use | 2007-12-01 | 구판 |
| 6 | ASTM A449-07b | Standard Specification for Hex Cap Screws, Bolts and Studs, Steel, Heat Treated, 120/105/90 ksi Minimum Tensile Strength, General Use | 2007-12-01 | 구판 |
| 7 | ASTM A449-07a | Standard Specification for Hex Cap Screws, Bolts and Studs, Steel, Heat Treated, 120/105/90 ksi Minimum Tensile Strength, General Use | 2007-08-01 | 구판 |
| 8 | ASTM A449-07 | Standard Specification for Hex Cap Screws, Bolts and Studs, Steel, Heat Treated, 120/105/90 ksi Minimum Tensile Strength, General Use | 2007-05-15 | 구판 |
| 9 | ASTM A449-04be1 | Specification for Hex Cap Screws, Bolts, and Studs, Steel, Heat Treated, 120/105/90 ksi Minimum Tensile Strength, General Use | 2004-11-01 | 구판 |
| 10 | ASTM A449-04b | Specification for Hex Cap Screws, Bolts, and Studs, Steel, Heat Treated, 120/105/90 ksi Minimum Tensile Strength, General Use | 2004-11-01 | 구판 |
| 11 | ASTM A449-04a | Standard Specification for Quenched and Tempered Steel Bolts and Studs | 2004-08-01 | 구판 |
| 12 | ASTM A449-04 | Standard Specification for Quenched and Tempered Steel Bolts and Studs | 2004-01-01 | 구판 |
| 13 | ASTM A449-00 | Standard Specification for Quenched and Tempered Steel Bolts and Studs | 2000-05-10 | 구판 |
| 14 | ASTM A449-78a | Standard Specification for Quenched And Tempered Steel Bolts And Studs | 구판 |
관련상품이 존재하지 않습니다.
ASTM A354-17e2 - Standard Specification for Quenched and Tempered Alloy Steel Bolts, Studs, and Other Externally Threaded Fasteners 상세보기
ASTM A1000/A1000M-17 - Standard Specification for Steel Wire, Carbon and Alloy Specialty Spring Quality 상세보기
ASTM F2882/F2882M-17 - Standard Specification for Screws, Alloy Steel, Heat Treated, 170 ksi and 1170 MPa Minimum Tensile Strength (Inch and Metric) 상세보기
ASTM F3148-17a - Standard Specification for High Strength Structural Bolt Assemblies, Steel and Alloy Steel, Heat Treated, 144ksi Minimum Tensile Strength, Inch Dimensions 상세보기
ASTM A877/A877M-17 - Standard Specification for Steel Wire, Chromium-Silicon Alloys, Chrome-Silicon-Vanadium Alloy Valve Spring Quality 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
