관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Standard Specification for Screws, Alloy Steel, Heat Treated, 170 ksi and 1170 MPa Minimum Tensile Strength (Inch and Metric)
| 분야 | 01.09 : 비철화스너 (구름요소베어링) |
|---|---|
| 적용범위 | 1.1 This specification covers the requirements for quenched and tempered alloy steel screws 0.060 through 11/2 in. and 1.6 through 48 mm in diameter having a minimum ultimate tensile strength of 170 KSI or 1170 MPa. 1.2 The values are stated in inch-pound units for inch fasteners and SI metric units for metric fasteners. The values stated in each system may not be exact equivalents; therefore each system shall be used independently of the other. Combining values from the two systems may result in non-conformance to the standard. 1.3 The following hazard caveat pertains only to the test method portion, Section 10, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | |
| 페이지수 | 7 |
| Edition | 17 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM F2882/F2882M-17 REDLINE | Standard Specification for Screws, Alloy Steel, Heat Treated, 170 ksi and 1170 MPa Minimum Tensile Strength (Inch and Metric) | 2017-06-01 | 표준 |
| 2 | ASTM F2882/F2882M-17 | Standard Specification for Screws, Alloy Steel, Heat Treated, 170 ksi and 1170 MPa Minimum Tensile Strength (Inch and Metric) | 2017-06-01 | 표준 |
관련상품이 존재하지 않습니다.
ASTM A400-17 - Standard Practice for Steel Bars, Selection Guide, Composition, and Mechanical Properties 상세보기
ASTM A1000/A1000M-17 - Standard Specification for Steel Wire, Carbon and Alloy Specialty Spring Quality 상세보기
ASTM F3148-17a - Standard Specification for High Strength Structural Bolt Assemblies, Steel and Alloy Steel, Heat Treated, 144ksi Minimum Tensile Strength, Inch Dimensions 상세보기
ASTM A877/A877M-17 - Standard Specification for Steel Wire, Chromium-Silicon Alloys, Chrome-Silicon-Vanadium Alloy Valve Spring Quality 상세보기
ASTM A713-04(2017) - Standard Specification for Steel Wire, High-Carbon Spring, for Heat-Treated Components 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
