관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
구판
판매
Standard Specification for Pressure Vessel Plates, Alloy Steel, Quenched and Tempered 7, 8, and 9 % Nickel
| 분야 | 01.04 : 철강-구조물, 보강재, 압력용기, 철도 | ||||||||
|---|---|---|---|---|---|---|---|---|---|
| 적용범위 | 1.1 This specification2 covers 7, 8, and 9 % nickel alloy steel plates for use in the water quenched and tempered condition intended for the fabrication of welded pressure vessels. 1.2 Material under this specification is available in three types having different chemical composition as follows:
1.3 Plates produced under this specification are subject to impact testing at −320°F [−195°C] for Type I or Type III, and −275°F [−170°C] for Type II; or at such other temperatures as are agreed upon. 1.4 The maximum thickness of plates is limited only by the capacity of the material to meet the specified mechanical property requirements; however, current mill practice normally limits this material to 2 in. [50 mm] max. 1.5 This material is susceptible to magnetization. Use of magnets in handling after heat treatment should be avoided if residual magnetism would be detrimental to subsequent fabrication or service. 1.6 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
||||||||
| 국제분류(ICS)코드 | 77.140.50 : 보통 강제품 및 반제품 | ||||||||
| 페이지수 | 4 | ||||||||
| Edition | 17e1 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM A553/A553M-22 | Standard Specification for Pressure Vessel Plates, Alloy Steel, Quenched and Tempered 7?%, 8?%, and 9 % Nickel | 2022-11-01 | 표준 |
| 2 | ASTM A553/A553M-22 REDLINE | Standard Specification for Pressure Vessel Plates, Alloy Steel, Quenched and Tempered 7?%, 8?%, and 9 % Nickel | 2022-11-01 | 표준 |
| 3 | ASTM A553/A553M-17e1 | Standard Specification for Pressure Vessel Plates, Alloy Steel, Quenched and Tempered 7, 8, and 9 % Nickel | 2017-11-01 | 구판 |
| 4 | ASTM A553/A553M-17 REDLINE | Standard Specification for Pressure Vessel Plates, Alloy Steel, Quenched and Tempered 7, 8, and 9 % Nickel | 2017-11-01 | 구판 |
| 5 | ASTM A553/A553M-17 | Standard Specification for Pressure Vessel Plates, Alloy Steel, Quenched and Tempered 7, 8, and 9 % Nickel | 2017-11-01 | 구판 |
| 6 | ASTM A553/A553M-14 | Standard Specification for Pressure Vessel Plates, Alloy Steel, Quenched and Tempered 7, 8, and 9 % Nickel | 2014-10-01 | 구판 |
| 7 | ASTM A553/A553M-10 | Standard Specification for Pressure Vessel Plates, Alloy Steel, Quenched and Tempered 8 and 9 Percent Nickel | 2010-10-01 | 구판 |
| 8 | ASTM A553/A553M-06 | Standard Specification for Pressure Vessel Plates, Alloy Steel, Quenched and Tempered 8 and 9 Percent Nickel | 2006-03-01 | 구판 |
| 9 | ASTM A553/A553M-95(2000) | Standard Specification for Pressure Vessel Plates, Alloy Steel, Quenched and Tempered 8 and 9 Percent Nickel | 2000-01-01 | 구판 |
관련상품이 존재하지 않습니다.
ASTM A387/A387M-17a - Standard Specification for Pressure Vessel Plates, Alloy Steel, Chromium-Molybdenum 상세보기
ASTM E96/E96M-16 - Standard Test Methods for Water Vapor Transmission of Materials 상세보기
ASTM E1257-16 - Standard Guide for Evaluating Grinding Materials Used for Surface Preparation in Spectrochemical Analysis 상세보기
ASTM B209-14 - Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate 상세보기
ASTM D1576-13 - Standard Test Method for Moisture in Wool by Oven-Drying (Withdrawn 2022) 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
