관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
분야 | 02.02 : 알루미늄 및 마그네슘 합금 |
---|---|
적용범위 | 1.1 This specification2 covers aluminum and aluminum-alloy flat sheet, coiled sheet, and plate in the alloys (Note 1) and tempers shown in Tables 2 and 3, and in the following finishes: (A) Limits are in weight percent maximum unless shown as a range or stated otherwise. (B) Analysis shall be made for the elements for which limits are shown in this table. (C) For purposes of determining conformance to these limits, an observed value or a calculated value attained from analysis shall be rounded to the nearest unit in the last righthand place of figures used in expressing the specified limit, in accordance with the Rounding Method of Practice E29. (D) Others includes listed elements for which no specific limit is shown as well as unlisted metallic elements. The producer may analyze samples for trace elements not specified in the specification. However, such analysis is not required and may not cover all metallic Others elements. Should any analysis by the producer or the purchaser establish that an Others element exceeds the limit of Each or that the aggregate of several Others elements exceeds the limit of Total, the material shall be considered nonconforming. The Total for Other Elements does not include elements shown in the footnotes with specific composition limits. (E) Other Elements—Total shall be the sum of unspecified metallic elements, 0.010 % or more, rounded to the second decimal before determining the sum. (F) Vanadium 0.05 max. (G) The aluminum content shall be calculated by subtracting from 100.00 % the sum of all metallic elements present in amounts of 0.010 % or more each, rounded to the second decimal before determining the sum. (H) Composition of cladding alloy as applied during the course of manufacture. Samples from finished sheet or plate shall not be required to conform to these limits. (I) Vanadium 0.05–0.15, zirconium 0.10–0.25. (J) 0.05–0.25 Zr (K) Gallium 0.03 max, vanadium 0.05 max. (L) 0.10–0.6 Mn + Cr. (M) In case there is a discrepancy in the values listed in Table 2 with those listed in the “International Alloy Designations and Chemical Composition Limits for Wrought Aluminum and Wrought Aluminum Alloys” (known as the “Teal Sheets”), the composition limits registered with the Aluminum Association and published in the “Teal Sheets” shall be considered the controlling composition. The “Teal Sheets” are available at http://www.aluminum.org/tealsheets. (A) To determine conformance to this specification each value for tensile strength and yield strength shall be rounded to the nearest 0.1 ksi and each value for elongation to the nearest 0.5 %, both in accordance with the Rounding Method of Practice E29. (B) The basis for establishment of mechanical property limits is shown in Annex A1. (C) Material in either of these tempers (H32 or H22), (H34 or H24), (H36 or H26), (H38 or H28), (H12 or H22), (H14 or H24), (H16 or H26), (H18 or H28), may be supplied at the option of the supplier, unless one is specifically excluded by the contract or purchase order. When ordered as H2x tempers, the maximum tensile strength and minimum yield strength do not apply. When H2x tempers are supplied instead of ordered H1x or H3x tempers, the supplied H2x temper material shall meet the respective H1x or H3x temper tensile property limits. (D) Tests of F temper plate for tensile properties are not required. (E) The tension test specimen from plate 0.500 in. and thicker is machined from the core and does not include the cladding alloy. (F) This material is subject to some recrystallization and an attendant loss of brightness. (A) To determine conformance to this specification, each value for tensile strength and yield strength shall be rounded to the nearest 0.1 ksi and each value for elongation to the nearest 0.5 %, both in accordance with the Rounding Method of Practice E29. (B) The basis for establishment of mechanical property limits is shown in Annex A1. (C) Long transverse unless otherwise noted. (D) Coiled sheet. (E) Material in the T42, T62, and T72 tempers is not available from the material producer. (F) For stress-relieved tempers (T351, T451, T651, T7351, T7651, and T851), characteristics and properties other than those specified may differ somewhat from the corresponding characteristics and properties of material in the basic temper. (G) Test for tensile properties in the F temper are not required. (H) The tension test specimen from plate 0.500 in. and thicker is machined from the core and does not include the cladding. (I) Applicable to flat sheet and plate only. (J) The T72 temper is applicable only to Alloys 2024 and Alclad 2024 sheet solution heat treated and artificially overaged by the user to develop increased resistance to stress-corrosion cracking. (K) Short transverse tensile property limits are not applicable to material less than 1.500 in. in thickness. (L) Use of Alloys 2219 and Alclad 2219 in the T31, T351, and T37 tempers for finished products is not recommended. (M) The properties for this thickness apply only to the T651 temper. 1.1.1 Plate in all alloys and sheet in heat-treatable alloys: mill finish. 1.1.2 Sheet in nonheat-treatable alloys: mill finish, one-side bright mill finish, standard one-side bright finish, and standard two-sides bright finish. 1.2 Alloy and temper designations are in accordance with ANSI H35.1/H35.1(M). The equivalent Unified Numbering System alloy designations are those of Table 1 preceded by A9, for example, A91100 for aluminum 1100 in accordance with Practice E527. Note 1: Throughout this specification, use of the term alloy in the general sense includes aluminum as well as aluminum alloy. Note 2: See Specification B632/B632M for tread plate. Note 3: See Specification B928/B928M for 5xxx-H116 and 5xxx-H321 aluminum alloys containing 3 % or more nominal magnesium and intended for marine service and similar environments. Other alloy-temper products listed in this specification, which do not require the additional corrosion testing/capability called out in ASTM B928/B928M, may be suitable for marine and similar environment applications. 1.3 For acceptance criteria for inclusion of new aluminum and aluminum alloys in this specification, see Annex A2. 1.4 This specification is the inch-pound companion to Specification B209M; therefore, no SI equivalents are presented in the specification. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
국제분류(ICS)코드 | 77.150.10 : 알루미늄 제품 |
페이지수 | 25 |
Edition | 14 |
No. | 표준번호 | 표준명 | 발행일 | 상태 |
---|---|---|---|---|
1 | ASTM B209-14 REDLINE | Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate | 2014-11-01 | 구판 |
2 | ASTM B209-14 | Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate | 2014-11-01 | 구판 |
3 | ASTM B209-10 | Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate | 2010-11-01 | 구판 |
4 | ASTM B209-07 | Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate | 2007-08-01 | 구판 |
5 | ASTM B209-06 | Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate | 2006-07-01 | 구판 |
6 | ASTM B209-04 | Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate | 2004-03-01 | 구판 |
7 | ASTM B209-02a | Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate | 2002-10-10 | 구판 |
8 | ASTM B209-02e1 | Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate | 2002-04-10 | 구판 |
9 | ASTM B209-00 | Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate | 2002-04-10 | 구판 |
10 | ASTM B209-01 | Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate | 2002-04-10 | 구판 |
11 | ASTM B209-02 | Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate | 2002-04-10 | 구판 |
12 | ASTM B209-93 | Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate | 구판 | |
13 | ASTM B209-96 | Standard Specification for Aluminum and Aluminum- Alloy Sheet and Plate | 구판 |
관련상품이 존재하지 않습니다.
ASTM A516/A516M-17 - Standard Specification for Pressure Vessel Plates, Carbon Steel, for Moderate- and Lower-Temperature Service 상세보기
ASTM A123/A123M-17 - Standard Specification for Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel Products 상세보기
ASTM C518-17 - Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Heat Flow Meter Apparatus 상세보기
ASTM C142/C142M-17 - Standard Test Method for Clay Lumps and Friable Particles in Aggregates 상세보기
ASTM E96/E96M-16 - Standard Test Methods for Water Vapor Transmission of Materials 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기