관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
구판
판매
Standard Practice for Sampling and Acceptance of Thermal Insulation Lots
| 분야 | 04.06 : 보온, 방음 |
|---|---|
| 적용범위 | 1.1 This practice covers criteria for establishing the acceptability of lots of shipments of preformed board, preformed block and pipe, and batts and blanket thermal insulation based on sampling and inspection. 1.2 This practice is intended for use in conjunction with appropriate ASTM material specifications that classify and describe the specific physical requirements for the product in terms of qualification requirements and inspection requirements. Determination of nonconformity shall be based on the tolerances for individual sample test values prescribed in the material specification. 1.3 This practice may require inspection substantially different from that performed in the normal course of production. If the purchaser requires sampling and acceptance inspection in accordance with this practice, he shall so specify in the order or contract. 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | 91.100.60 : 방열 및 방음 재료 |
| 페이지수 | 4 |
| Edition | 08(2019) |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM C390-08(2024) | Standard Practice for Sampling and Acceptance of Thermal Insulation Lots | 2024-03-01 | 표준 |
| 2 | CSA C390:22 | Test method, marking requirements, and energy efficiency levels for three-phase induction motors | 2022-01-01 | 표준 |
| 3 | ASTM C390-08(2019) | Standard Practice for Sampling and Acceptance of Thermal Insulation Lots | 2019-09-01 | 구판 |
| 4 | ASTM C390-08(2013) | Standard Practice for Sampling and Acceptance of Thermal Insulation Lots | 2013-11-01 | 구판 |
| 5 | ASTM C390-08e1 | Standard Practice for Sampling and Acceptance of Thermal Insulation Lots | 2008-04-15 | 구판 |
| 6 | ASTM C390-08 | Standard Practice for Sampling and Acceptance of Thermal Insulation Lots | 2008-04-15 | 구판 |
| 7 | ASTM C390-03 | Standard Practice for Sampling and Acceptance of Thermal Insulation Lots | 2003-04-10 | 구판 |
| 8 | ASTM C390-02 | Standard Practice for Sampling and Acceptance of Thermal Insulation Lots | 2002-09-10 | 구판 |
| 9 | ASTM C390-79(2000) | Standard Criteria for Sampling and Acceptance of Preformed Thermal Insulation Lots | 2000-04-10 | 구판 |
관련상품이 존재하지 않습니다.
ASTM D792-13 - Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement 상세보기
ASTM D1622/D1622M-14 - Standard Test Method for Apparent Density of Rigid Cellular Plastics 상세보기
ASTM D638-14 - Standard Test Method for Tensile Properties of Plastics 상세보기
ASTM D695-15 - Standard Test Method for Compressive Properties of Rigid Plastics 상세보기
ASTM D6226-15 - Standard Test Method for Open Cell Content of Rigid Cellular Plastics 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
