관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Standard Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe
| 분야 | 08.04 : 플라스틱 파이프 및 건축용 제품 |
|---|---|
| 적용범위 | 1.1 This test method covers the determination of the comparative apparent tensile strength of most plastic products utilizing a split disk or ring segment test fixture, when tested under defined conditions of pretreatment, temperature, humidity, and test machine speed. This test method is applicable to reinforced-thermosetting resin pipe regardless of fabrication method. This test method also is applicable to extruded and molded thermoplastic pipe. Procedure A is used for reinforced-thermosetting resin pipe; Procedure B is used for thermoplastic pipe of any size; Procedure C is used for thermoplastic pipe with nominal diameter of 41/2 in. (110 mm) and greater. Procedure D is used for polyethylene pipe with a nominal diameter of 14 in. (350 mm) and greater and preferably having wall thickness 1 in. (25 mm) and greater. Procedure E is used for polyvinyl chloride (PVC) pipe with a nominal diameter of 14 in. (350 mm) and greater and having wall thickness 0.5 in. (12.7 mm) and greater. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | 83.120 : 강화 플라스틱 |
| 페이지수 | 11 |
| Edition | 19a |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM D2290-19a | Standard Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe | 2019-08-01 | 표준 |
| 2 | ASTM D2290-19a REDLINE | Standard Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe | 2019-08-01 | 표준 |
| 3 | ASTM D2290-19 | Standard Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe | 2019-01-01 | 구판 |
| 4 | ASTM D2290-16 | Standard Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe | 2016-08-01 | 구판 |
| 5 | ASTM D2290-16 REDLINE | Standard Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe | 2016-08-01 | 구판 |
| 6 | ASTM D2290-12 | Standard Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe | 2012-12-01 | 구판 |
| 7 | ASTM D2290-08 | Standard Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe by Split Disk Method | 2008-11-01 | 구판 |
| 8 | ASTM D2290-04 | Standard Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe by Split Disk Method | 2004-09-01 | 구판 |
| 9 | ASTM D2290-00e1 | Standard Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe by Split Disk Method | 2000-06-10 | 구판 |
| 10 | ASTM D2290-00 | Standard Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe by Split Disk Method | 2000-06-10 | 구판 |
관련상품이 존재하지 않습니다.
ASTM D1599-18 - Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings 상세보기
ASTM D2412-21 - Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading 상세보기
ASTM D2310-06(2012) - Standard Classification for Machine-Made “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe (Withdrawn 2017) 상세보기
ASTM D638-14 - Standard Test Method for Tensile Properties of Plastics 상세보기
ASTM D3261-16 - Standard Specification for Butt Heat Fusion Polyethylene (PE) Plastic Fittings for Polyethylene (PE) Plastic Pipe and Tubing 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
