관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Standard Practice for Quality Assurance of Pressure-Sensitive Tapes
| 분야 | |
|---|---|
| 적용범위 | 1.1 This practice contains uniform quality assurance provisions for pressure-sensitive tapes and establishes sampling plans and procedures for acceptance inspection. 1.2 Limitations: 1.2.1 This practice only includes procedures for when an upper or a lower specification limit is given. It does not provide for double, both minimum and maximum, specification limits. Note 1: When double specification limits are given (applies to variables testing only), use may be made of Table C-3 and Example C-3 of ANSI/ASQC Z1.9. 1.2.2 The variables sampling plans apply to a single quality characteristic. Having obtained the sample and the responses to the physical property tests, acceptance is determined on one quality characteristic at a time. The process is repeated for each additional characteristic. 1.2.3 The variables sampling plans require that the response to each quality characteristic is normally distributed either directly or by transformation. If this is not known, the potential user of this practice should seek the counsel of someone with sufficient understanding of statistical techniques to provide that information. 1.3 The values stated in either SI or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system must be used independently, without combining values in any way. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | 83.180 : 접착제 |
| 페이지수 | 6 |
| Edition | 98(2019) |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM D3715/D3715M-98(2019) | Standard Practice for Quality Assurance of Pressure-Sensitive Tapes | 2019-08-01 | 표준 |
| 2 | ASTM D3715/D3715M-98(2011) | Standard Practice for Quality Assurance of Pressure-Sensitive Tapes | 2011-04-01 | 구판 |
| 3 | ASTM D3715/D3715M-98 | Standard Practice for Quality Assurance of Pressure-Sensitive Tapes | 1998-04-10 | 구판 |
| 4 | ASTM D3715/D3715M-98(2004) | Standard Practice for Quality Assurance of Pressure-Sensitive Tapes | 1998-04-10 | 구판 |
관련상품이 존재하지 않습니다.
ASTM D3330/D3330M-04(2018) - Standard Test Method for Peel Adhesion of Pressure-Sensitive Tape 상세보기
ASTM D6252/D6252M-98(2019) - Standard Test Method for Peel Adhesion of Pressure-Sensitive Label Stocks at a 90° Angle 상세보기
ASTM D5750/D5750M-95(2020) - Standard Guide for Width and Length of Pressure-Sensitive Tape 상세보기
ASTM F1980-16 - Standard Guide for Accelerated Aging of Sterile Barrier Systems for Medical Devices 상세보기
ASTM D4169-16 - Standard Practice for Performance Testing of Shipping Containers and Systems 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
