관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Standard Test Method for Peel Adhesion of Pressure-Sensitive Tape
| 분야 | 15.10 : 포장 |
|---|---|
| 적용범위 | 1.1 These test methods cover the measurement of the peel adhesion of pressure-sensitive tapes. 1.1.1 Test Method A gives a measure of the adherence, when peeled at 180° angle, to a standard steel panel or to other surface of interest for a single-coated tape. 1.1.2 Test Method B gives a measure of the adherence to the backing of a single-coated tape. 1.1.3 Test Method C gives a measure of the adherence of double-coated tape to a standard steel panel or other surface of interest. 1.1.4 Test Method D gives a measure of the adherence of the release liner to the adhesive of either single- or double-coated tape. 1.1.5 Test Method E gives a measure of the adherence of an adhesive transfer tape to a standard steel panel or other surface of interest. 1.1.6 Test Method F gives a measure of the adherence, when peeled at 90° angle, to a standard steel panel or other surface of interest for a single-coated tape. 1.2 These test methods provide a means of assessing the uniformity of the adhesion of a given type of pressure-sensitive adhesive tape. The assessment may be within a roll of tape, between rolls, or between production lots. 1.3 Variations in either the tape backing or the adhesive, or both, affect the response. Therefore, these test methods cannot be used to pinpoint the specific cause(s) of non-uniformity. 1.4 These test methods may not be appropriate to test tapes having relatively stiff backings, stiff liners, or backings showing high stretch at low forces. These characteristics will result in a high variability for the test response which is not a true indication of the real nature of the adhesive bond. 1.5 Values stated in either SI or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents, therefore, each system must be used independently without combining values in any way. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | |
| 페이지수 | 6 |
| Edition | 04(2018) |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM D3330/D3330M-04(2018) | Standard Test Method for Peel Adhesion of Pressure-Sensitive Tape | 2018-10-01 | 표준 |
| 2 | ASTM D3330/D3330M-04(2010) | Standard Test Method for Peel Adhesion of Pressure-Sensitive Tape | 2010-04-01 | 구판 |
| 3 | ASTM D3330/D3330M-04 | Standard Test Method for Peel Adhesion of Pressure-Sensitive Tape | 2004-10-01 | 구판 |
| 4 | ASTM D3330/D3330M-02e1 | Standard Test Method for Peel Adhesion of Pressure-Sensitive Tape | 2002-10-10 | 구판 |
| 5 | ASTM D3330/D3330M-02 | Standard Test Method for Peel Adhesion of Pressure-Sensitive Tape | 2002-10-10 | 구판 |
| 6 | ASTM D3330/D3330M-00 | Standard Test Method for Peel Adhesion of Pressure-Sensitive Tape | 2000-10-10 | 구판 |
관련상품이 존재하지 않습니다.
BS EN 13726-1:2002 - Test methods for primary wound dressings. Aspects of absorbency. 상세보기
ASTM F2450-18 REDLINE - Standard Guide for Assessing Microstructure of Polymeric Scaffolds for Use in Tissue-Engineered Medical Products 상세보기
ASTM F1408-97(2013) - Standard Practice for Subcutaneous Screening Test for Implant Materials 상세보기
ASTM F981-04(2016) - Standard Practice for Assessment of Compatibility of Biomaterials for Surgical Implants with Respect to Effect of Materials on Muscle and Insertion into Bone 상세보기
ASTM F2902-16e1 - Standard Guide for Assessment of Absorbable Polymeric Implants 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
