관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
구판
판매
Standard Test Methods for Physical Dimensions of Solid Plastics Specimens
| 분야 | 08.03 : 플라스틱 (Ⅲ) |
|---|---|
| 적용범위 | 1.1 These test methods cover determination of the physical dimensions of solid plastic specimens where the dimensions are used directly in determining the results of tests for various properties. Use these test methods except as otherwise required in material specifications. 1.2 The values stated in SI units are to be regarded as standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Note 1: This standard and ISO 16012 address the same subject matter, but differ in technical content. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | 83.080.01 : 플라스틱 일반 |
| 페이지수 | 10 |
| Edition | 18 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM D5947-24 | Standard Test Methods for Physical Dimensions of Solid Plastics Specimens | 2024-04-15 | 표준 |
| 2 | ASTM D5947-24 REDLINE | Standard Test Methods for Physical Dimensions of Solid Plastics Specimens | 2024-04-15 | 표준 |
| 3 | ASTM D5947-18 | Standard Test Methods for Physical Dimensions of Solid Plastics Specimens | 2018-08-01 | 구판 |
| 4 | ASTM D5947-18 REDLINE | Standard Test Methods for Physical Dimensions of Solid Plastics Specimens | 2018-08-01 | 구판 |
| 5 | ASTM D5947-11 | Standard Test Methods for Physical Dimensions of Solid Plastics Specimens | 2011-12-15 | 구판 |
| 6 | ASTM D5947-06 | Standard Test Methods for Physical Dimensions of Solid Plastics Specimens | 2006-04-01 | 구판 |
| 7 | ASTM D5947-03 | Standard Test Methods for Physical Dimensions of Solid Plastics Specimens | 2003-07-10 | 구판 |
| 8 | ASTM D5947-02 | Standard Test Methods for Physical Dimensions of Solid Plastics Specimens | 2002-08-10 | 구판 |
| 9 | ASTM D5947-01e1 | Standard Test Methods for Physical Dimensions of Solid Plastics Specimens | 2001-10-10 | 구판 |
| 10 | ASTM D5947-96 | Standard Test Methods for Physical Dimensions of Solid Plastics Specimens | 2001-10-10 | 구판 |
관련상품이 존재하지 않습니다.
ASTM D726-94(2003) - Standard Test Method for Resistance of Nonporous Paper to Passage of Air (Withdrawn 2009) 상세보기
ASTM D2873-94(1999)e1 - Standard Test Method for Interior Porosity of Poly(Vinyl Chloride) (PVC) Resins by Mercury Intrusion Porosimetry (Withdrawn 2003) 상세보기
ASTM D2103-15 - Standard Specification for Polyethylene Film and Sheeting 상세보기
ASTM D882-18 - Standard Test Method for Tensile Properties of Thin Plastic Sheeting 상세보기
ASTM D3763-18 - Standard Test Method for High Speed Puncture Properties of Plastics Using Load and Displacement Sensors 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
