관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
분야 | 08.01 : 플라스틱 (Ⅰ) |
---|---|
적용범위 | 1.1 This test method describes a procedure for measuring the interior pore volume and the apparent pore diameter distribution of porous poly(vinyl chloride) resins. The measurements are made by forcing mercury under increasing pressure through a graduated penetrometer into the open pores of the resin samples. The volume of mercury forced into the pores is defined from the change of the mercury volume in the penetrometer; the apparent pore diameter distribution can be defined from incremental volume changes with increasing pressure. 1.2 Warning-This standard includes the use of an OSHA-designated hazardous chemical (Mercury). For specific hazard information and guidance relative to use, consult the health and safety documents provided by the supplier, for example, the material safety data sheet. 1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Note 1-There are no ISO standards covering the primary subject matter of this test method. |
국제분류(ICS)코드 | |
페이지수 | 3 |
Edition | 94(1999)e1 |
No. | 표준번호 | 표준명 | 발행일 | 상태 |
---|---|---|---|---|
1 | ASTM D2873-94(1999)e1 | Standard Test Method for Interior Porosity of Poly(Vinyl Chloride) (PVC) Resins by Mercury Intrusion Porosimetry (Withdrawn 2003) | 1999-07-10 | 폐지 |
관련상품이 존재하지 않습니다.
ASTM D1204-14(2020) - Standard Test Method for Linear Dimensional Changes of Nonrigid Thermoplastic Sheeting or Film at Elevated Temperature 상세보기
ASTM D3763-18 - Standard Test Method for High Speed Puncture Properties of Plastics Using Load and Displacement Sensors 상세보기
ASTM D882-18 - Standard Test Method for Tensile Properties of Thin Plastic Sheeting 상세보기
ASTM D5947-18 - Standard Test Methods for Physical Dimensions of Solid Plastics Specimens 상세보기
ASTM D2103-15 - Standard Specification for Polyethylene Film and Sheeting 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기