관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
구판
판매
Standard Practice for Characterization and Verification of Phased Array Probes
| 분야 | 03.04 : 비 파괴검사 (Ⅱ) |
|---|---|
| 적용범위 | 1.1 This standard practice covers measurement procedures for evaluating certain characteristics of phased-array ultrasonic probes that are used with phased-array ultrasonic examination instrumentation. 1.2 This standard practice describes means for obtaining performance data that may be used to define the acoustic and electric responses of phased-array ultrasonic probes including contact (with or without a wedge) and immersion linear phased-array probes used for ultrasonic nondestructive testing with central frequencies ranging from 0.5 MHz to 10 MHz. Frequencies outside of this range may use the same methods but the testing equipment may vary. 1.3 When ultrasonic values dependent on material are specified in this document, they are based on carbon steel with an ultrasonic wave propagation speed of 5920 m/s (±50 m/s) for longitudinal wave modes and 3255 m/s (±30 m/s) for transverse or shear wave modes. 1.4 This document describes some of the characterization and verification procedures that can be carried out at the end stage of the manufacturing process of phased array probes. This document does not describe the methods or acceptance criteria used to verify the performance of the combined phased array ultrasonic instrument and probe system. 1.5 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | 19.100 : 비파괴 시험 및 기구 |
| 페이지수 | 7 |
| Edition | 17 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM E2904-22 | Standard Practice for Characterization and Verification of Linear Phased Array Ultrasonic Probes | 2022-12-01 | 표준 |
| 2 | ASTM E2904-22 REDLINE | Standard Practice for Characterization and Verification of Linear Phased Array Ultrasonic Probes | 2022-12-01 | 표준 |
| 3 | ASTM E2904-17 REDLINE | Standard Practice for Characterization and Verification of Phased Array Probes | 2017-11-01 | 구판 |
| 4 | ASTM E2904-17 | Standard Practice for Characterization and Verification of Phased Array Probes | 2017-11-01 | 구판 |
| 5 | ASTM E2904-12 | Standard Practice for Characterization and Verification of Phased Array Probes | 2012-11-01 | 구판 |
관련상품이 존재하지 않습니다.
ASTM E1065/E1065M-14 - Standard Guide for Evaluating Characteristics of Ultrasonic Search Units 상세보기
ASTM E2491-13(2018) - Standard Guide for Evaluating Performance Characteristics of Phased-Array Ultrasonic Testing Instruments and Systems 상세보기
ASTM E317-21 - Standard Practice for Evaluating Performance Characteristics of Ultrasonic Pulse-Echo Testing Instruments and Systems without the Use of Electronic Measurement Instruments 상세보기
ASTM E2700-20 - Standard Practice for Contact Ultrasonic Testing of Welds Using Phased Arrays 상세보기
ASTM E3170/E3170M-18 - Standard Practice for Phased Array Ultrasonic Testing of Polyethylene Electrofusion Joints 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
