관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Standard Practice for Contact Ultrasonic Testing of Welds Using Phased Arrays
| 분야 | 03.04 : 비 파괴검사 (Ⅱ) |
|---|---|
| 적용범위 | 1.1 This practice describes ultrasonic techniques for examining welds using phased array ultrasonic methods (see Note 1 and Note 2). 1.2 This practice uses angle beams, either in S-scan or E-scan modes, primarily for butt welds and Tee welds. Alternative welding techniques, such as solid state bonding (for example, friction stir welding) and fusion welding (for example, electron beam welding) can be examined using this practice, provided adequate coverage and techniques are documented and approved. Practices for specific geometries such as spot welds are not included. The practice is intended to be used on thicknesses of 9 to 200 mm. Greater and lesser thicknesses may be examined using this practice if the technique can be demonstrated to provide adequate detection on mockups of the same wall thickness and geometry. 1.2.1 Extreme caution should be used when attempting to size indications using phased array. It is likely that without proper procedures, indications can be oversized due to beam divergence, multiple virtual probes returning signals from the same indication, etc. For more guidance, see 12.4. 1.3 Units—The values stated in SI units are to be regarded as standard. Note 1: This practice is based on experience with ferrous and aluminum alloys. Other metallic materials can be examined using this practice, provided reference standards can be developed to demonstrate that the particular material and weld can be successfully penetrated by an ultrasonic beam. Note 2: For additional pertinent information, see ASME BPVC Section V, Article 4, Guide E2491, Practice E317, and Practice E587. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. |
| 국제분류(ICS)코드 | 25.160.40 : 용접이음 |
| 페이지수 | 10 |
| Edition | 20 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM E2700-20 | Standard Practice for Contact Ultrasonic Testing of Welds Using Phased Arrays | 2020-06-01 | 표준 |
| 2 | ASTM E2700-20 REDLINE | Standard Practice for Contact Ultrasonic Testing of Welds Using Phased Arrays | 2020-06-01 | 표준 |
| 3 | ASTM E2700-14 REDLINE | Standard Practice for Contact Ultrasonic Testing of Welds Using Phased Arrays | 2014-10-01 | 구판 |
| 4 | ASTM E2700-14 | Standard Practice for Contact Ultrasonic Testing of Welds Using Phased Arrays | 2014-10-01 | 구판 |
| 5 | ASTM E2700-09 | Standard Practice for Contact Ultrasonic Testing of Welds Using Phased Arrays | 2009-08-01 | 구판 |
관련상품이 존재하지 않습니다.
ASTM E213-22 - Standard Practice for Ultrasonic Testing of Metal Pipe and Tubing 상세보기
ASTM E376-19 - Standard Practice for Measuring Coating Thickness by Magnetic-Field or Eddy Current (Electromagnetic) Testing Methods 상세보기
ASTM E2491-13(2018) - Standard Guide for Evaluating Performance Characteristics of Phased-Array Ultrasonic Testing Instruments and Systems 상세보기
ASTM E3170/E3170M-18 - Standard Practice for Phased Array Ultrasonic Testing of Polyethylene Electrofusion Joints 상세보기
ASTM E2734/E2734M-10(2018) - Standard Specification for Dimensions of Knife-Edge Flanges 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
