관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
구판
판매
Standard Test Method for Tensile Properties of Fiber Reinforced Polymer Matrix Composite Bars
| 분야 | 15.03 : 공간시물레이션; 항공우주재료; 고율섬유와 합성물 |
|---|---|
| 적용범위 | 1.1 This test method determines the quasi-static longitudinal tensile strength and elongation properties of fiber reinforced polymer matrix (FRP) composite bars commonly used as tensile elements in reinforced, prestressed, or post-tensioned concrete. Note 1: Additional procedures for determining tensile properties of polymer matrix composites may be found in test methods D3039/D3039M and D3916. 1.2 Linear elements used for reinforcing Portland cement concrete are referred to as bars, rebar, rods, or tendons, depending on the specific application. This test method is applicable to all such reinforcements within the limitations noted in the method. The test articles are referred to as bars in this test method. In general, bars have solid cross-sections and a regular pattern of surface undulations and/or a coating of bonded particles that promote mechanical interlock between the bar and concrete. The test method is also appropriate for use with linear segments cut from a grid. Specific details for preparing and testing of bars and grids are provided. In some cases, anchors may be necessary to prevent grip-induced damage to the ends of the bar or grid. Recommended details for the anchors are provided in Annex A1. 1.3 The strength values provided by this method are short-term static strengths that do not account for sustained static or fatigue loading. Additional material characterization may be required, especially for bars that are to be used under high levels of sustained or repeated loading. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4.1 Within the text, the inch-pound units are shown in brackets. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
| 국제분류(ICS)코드 | 91.100.40 : 섬유 강화 시멘트 제품 |
| 페이지수 | 13 |
| Edition | 06(2016) |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM D7205/D7205M-21 | Standard Test Method for Tensile Properties of Fiber Reinforced Polymer Matrix Composite Bars | 2021-05-15 | 표준 |
| 2 | ASTM D7205/D7205M-21 REDLINE | Standard Test Method for Tensile Properties of Fiber Reinforced Polymer Matrix Composite Bars | 2021-05-15 | 표준 |
| 3 | ASTM D7205/D7205M-06(2016) | Standard Test Method for Tensile Properties of Fiber Reinforced Polymer Matrix Composite Bars | 2016-11-01 | 구판 |
| 4 | ASTM D7205/D7205M-06(2011) | Standard Test Method for Tensile Properties of Fiber Reinforced Polymer Matrix Composite Bars | 2011-08-01 | 구판 |
| 5 | ASTM D7205/D7205M-06 | Standard Test Method for Tensile Properties of Fiber Reinforced Polymer Matrix Composite Bars | 2006-03-15 | 구판 |
관련상품이 존재하지 않습니다.
ASTM D790-17 - Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials 상세보기
ASTM C773-88(2016) - Standard Test Method for Compressive (Crushing) Strength of Fired Whiteware Materials 상세보기
ASTM D695-15 - Standard Test Method for Compressive Properties of Rigid Plastics 상세보기
ASTM C20-00(2015) - Standard Test Methods for Apparent Porosity, Water Absorption, Apparent Specific Gravity, and Bulk Density of Burned Refractory Brick and Shapes by Boiling Water 상세보기
ASTM D638-14 - Standard Test Method for Tensile Properties of Plastics 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
