관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
구판
판매
Standard Test Method for Measuring Relative Movement Capabilities of Through-Penetration Firestop Systems
| 분야 | 04.12 : 건축 (Ⅱ) |
|---|---|
| 적용범위 | 1.1 This test method covers testing procedures for through-penetration firestop systems. This test method is intended for the following uses: Note 1: Refer to Test Method E814 for definition of “through-penetration firestop system.” 1.1.1 To determine relative movement capability in two separate and distinct planes of movement for different types of through-penetration firestop systems, 1.1.2 To standardize a comparison of movement capability by establishing standardized test conditions, in order to allow the type of through-penetration firestop system’s movement capabilities to be examined, 1.1.3 To provide the user with information on amplitudes of relative movement between the penetrating items and the substrate (concrete-based or gypsum-based). Note 2: Amplitude is the measure of change over a single cycle. 1.2 This test method is intended to be used only as part of a specification or acceptance criteria due to the limited movements tested, and limited number of variables examined. 1.3 This test method uses standardized configurations for the test specimen. Test results will not be representative of all possible through-penetration firestop systems. 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 The text of this standard references notes, comments, and footnotes which provide explanatory material. These notes, comments, and footnotes (excluding those in tables and figures) shall not be considered requirements of this standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Some specific hazards statements are given in Section 7 on Safety Hazards. |
| 국제분류(ICS)코드 |
13.220.50 : 건물자재 및 요소의 내화성
23.040.99 : 기타 파이프라인 부품 91.060.10 : 벽. 칸막이. 건물의 외관 |
| 페이지수 | 10 |
| Edition | 16 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM E3037-20 | Standard Test Method for Measuring Relative Movement Capabilities of Through-Penetration Firestop Systems | 2020-07-01 | 표준 |
| 2 | ASTM E3037-20 REDLINE | Standard Test Method for Measuring Relative Movement Capabilities of Through-Penetration Firestop Systems | 2020-07-01 | 표준 |
| 3 | ASTM E3037-19 | Standard Test Method for Measuring Relative Movement Capabilities of Through-Penetration Firestop Systems | 2019-12-01 | 구판 |
| 4 | ASTM E3037-19 REDLINE | Standard Test Method for Measuring Relative Movement Capabilities of Through-Penetration Firestop Systems | 2019-12-01 | 구판 |
| 5 | ASTM E3037-16 | Standard Test Method for Measuring Relative Movement Capabilities of Through-Penetration Firestop Systems | 2016-10-01 | 구판 |
관련상품이 존재하지 않습니다.
ASTM E3038-16 - Standard Practice for Assessing and Qualifying Candidates as Inspectors of Firestop Systems and Fire-Resistive Joint Systems 상세보기
ASTM E2393-10a(2015) - Standard Practice for On-Site Inspection of Installed Fire Resistive Joint Systems and Perimeter Fire Barriers 상세보기
ASTM E1966-15 - Standard Test Method for Fire-Resistive Joint Systems 상세보기
ASTM E2786-10(2015) - Standard Test Methods for Measuring Expansion of Intumescent Materials Used in Firestop and Joint Systems 상세보기
ASTM E2923-14 - Standard Practice for Longevity Assessment of Firestop Materials Using Differential Scanning Calorimetry 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
