관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
구판
판매
Standard Practice for Longevity Assessment of Firestop Materials Using Differential Scanning Calorimetry
| 분야 | 04.12 : 건축 (Ⅱ) |
|---|---|
| 적용범위 | 1.1 This practice covers a standardized procedure for quantitatively assessing the longevity of materials used in firestop systems, by the use of data obtained from differential scanning calorimetry. 1.2 This practice is intended to differentiate firestop materials that are expected to maintain performance characteristics over time from those that are expected to degrade in performance characteristics over time. DSC experimental curve evaluation can also deliver indifferent results, where an interpretation of sample properties is not possible without additional testing using conventional durability testing. It evaluates the extent of chemical reactions that will occur within the firestop material under specified conditions of temperature and humidity. This practice does not measure longevity under specific severe environmental conditions or building operation that might be experienced by an individual firestop system. 1.3 This practice is intended to be used to test the materials used within a firestopping system. The practice is not intended to be used to test the properties of assembled firestopping systems. 1.4 This practice is intended to evaluate the following types of materials used in through-penetration fire stops: 1.4.1 Endothermic, 1.4.2 Intumescent, 1.4.3 Insulation, 1.4.4 Ablatives, and 1.4.5 Subliming. 1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Some specific hazards are given in Section 8 on Hazards. |
| 국제분류(ICS)코드 | 13.220.20 : 방화 장비 |
| 페이지수 | 5 |
| Edition | 14 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM E2923-14(2019) | Standard Practice for Longevity Assessment of Firestop Materials Using Differential Scanning Calorimetry | 2019-10-01 | 표준 |
| 2 | ASTM E2923-14 | Standard Practice for Longevity Assessment of Firestop Materials Using Differential Scanning Calorimetry | 2014-05-01 | 구판 |
| 3 | ASTM E2923-14 REDLINE | Standard Practice for Longevity Assessment of Firestop Materials Using Differential Scanning Calorimetry | 2014-05-01 | 구판 |
| 4 | ASTM E2923-13 | Standard Practice for Longevity Assessment of Firestop Materials Using Differential Scanning Calorimetry | 2013-04-01 | 구판 |
관련상품이 존재하지 않습니다.
ASTM E3037-16 - Standard Test Method for Measuring Relative Movement Capabilities of Through-Penetration Firestop Systems 상세보기
ASTM E3038-16 - Standard Practice for Assessing and Qualifying Candidates as Inspectors of Firestop Systems and Fire-Resistive Joint Systems 상세보기
ASTM E2393-10a(2015) - Standard Practice for On-Site Inspection of Installed Fire Resistive Joint Systems and Perimeter Fire Barriers 상세보기
ASTM E1966-15 - Standard Test Method for Fire-Resistive Joint Systems 상세보기
ASTM E2786-10(2015) - Standard Test Methods for Measuring Expansion of Intumescent Materials Used in Firestop and Joint Systems 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
