관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
구판
판매
Standard Test Method for Linearly Reciprocating Ball-on-Flat Sliding Wear
| 분야 | 03.02 : 마모 및 침식;금속 부식 |
|---|---|
| 적용범위 | 1.1 This test method covers laboratory procedures for determining the sliding wear of ceramics, metals, and other candidate wear-resistant materials using a linear, reciprocating ball-on-flat plane geometry. The direction of the relative motion between sliding surfaces reverses in a periodic fashion such that the sliding occurs back and forth and in a straight line. The principal quantities of interest are the wear volumes of the contacting ball and flat specimen materials; however, the coefficient of kinetic friction may also be measured using the method described. This test method encompasses both unlubricated and lubricated testing procedures. The scope of this test method does not include testing in corrosive or chemically aggressive environments. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
| 국제분류(ICS)코드 | 19.060 : 기계 시험과 기구 |
| 페이지수 | 9 |
| Edition | 05(2016) |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM G133-22 | Standard Test Method for Linearly Reciprocating Ball-on-Flat Sliding Wear | 2022-11-01 | 표준 |
| 2 | ASTM G133-22 REDLINE | Standard Test Method for Linearly Reciprocating Ball-on-Flat Sliding Wear | 2022-11-01 | 표준 |
| 3 | ASTM G133-05(2016) | Standard Test Method for Linearly Reciprocating Ball-on-Flat Sliding Wear | 2016-06-01 | 구판 |
| 4 | ASTM G133-05(2010) | Standard Test Method for Linearly Reciprocating Ball-on-Flat Sliding Wear | 2010-04-01 | 구판 |
| 5 | ASTM G133-05e1 | Standard Test Method for Linearly Reciprocating Ball-on-Flat Sliding Wear | 2005-05-01 | 구판 |
| 6 | ASTM G133-05 | Standard Test Method for Linearly Reciprocating Ball-on-Flat Sliding Wear | 2005-05-01 | 구판 |
| 7 | ASTM G133-02 | Standard Test Method for Linearly Reciprocating Ball-on-Flat Sliding Wear | 2002-11-10 | 구판 |
| 8 | ASTM G133-95(2002)e1 | Standard Test Method for Linearly Reciprocating Ball-on-Flat Sliding Wear | 1995-10-10 | 구판 |
| 9 | ASTM G133-95 | Standard Test Method for Linearly Reciprocating Ball-on-Flat Sliding Wear | 1995-01-01 | 구판 |
관련상품이 존재하지 않습니다.
ASTM D412-16 - Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers—Tension 상세보기
ASTM D8015-15 - Standard Test Method for Dimensional Changes of Elastomer and Rubber Materials Due to Exposure to Gaseous Hydrocarbon Environments 상세보기
ASTM E595-15 - Standard Test Method for Total Mass Loss and Collected Volatile Condensable Materials from Outgassing in a Vacuum Environment 상세보기
ASTM D638-14 - Standard Test Method for Tensile Properties of Plastics 상세보기
ASTM D792-13 - Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
