관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
구판
판매
Standard Test Method for Indentation Softening Temperature by Thermomechanical Analysis
| 분야 | 14.05 : 통계 방법; 화학 물질의 잠재적 위험성; 열측정; 약품 제조 |
|---|---|
| 적용범위 | 1.1 This test method is applicable to materials that soften upon heating to a modulus less than 6.0 MPa. This test method describes the determination of the temperature at which the specific modulus of either 6.65 (Method A) or 33.3 MPa (Method B) (equivalent to Test Method D1525) of a test specimen is realized by indentation measurement using a thermomechanical analyzer as the test specimen is heated. This temperature is identified as the indentation softening temperature. The test may be performed over the temperature range of ambient to 300°C. Note 1: This test method is intended to provide results similar to those of Test Method D1525 but is performed on a thermomechanical analyzer using a smaller diameter indenting probe. Equivalence of results to those obtained by Test Method D1525 has been demonstrated on a limited number of materials. Until the user demonstrates equivalence, the results of this Test Method shall be considered to be independent and unrelated to those of Test Method D1525. 1.2 This test method is not recommended for ethyl cellulose, poly (vinyl chloride), poly (vinylidene chloride) and other materials having a large measurement imprecision (see Test Method D1525 and 5.3 and Section 14). 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 There is no ISO standard equivalent to this test method. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
| 국제분류(ICS)코드 | 83.080.01 : 플라스틱 일반 |
| 페이지수 | 5 |
| Edition | 16 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM E2347-21 | Standard Test Method for Indentation Softening Temperature by Thermomechanical Analysis | 2021-07-01 | 표준 |
| 2 | ASTM E2347-21 REDLINE | Standard Test Method for Indentation Softening Temperature by Thermomechanical Analysis | 2021-07-01 | 표준 |
| 3 | ASTM E2347-16 | Standard Test Method for Indentation Softening Temperature by Thermomechanical Analysis | 2016-04-01 | 구판 |
| 4 | ASTM E2347-16 REDLINE | Standard Test Method for Indentation Softening Temperature by Thermomechanical Analysis | 2016-04-01 | 구판 |
| 5 | ASTM E2347-11 | Standard Test Method for Indentation Softening Temperature by Thermomechanical Analysis | 2011-04-01 | 구판 |
| 6 | ASTM E2347-05 | Standard Test Method for Indentation Softening Temperature by Thermomechanical Analysis | 2005-09-01 | 구판 |
| 7 | ASTM E2347-04 | Standard Test Method for Indentation Softening Temperature by Thermomechanical Analysis | 2004-02-01 | 구판 |
관련상품이 존재하지 않습니다.
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
