관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
구판
판매
Standard Test Methods for Determining Average Grain Size Using Semiautomatic and Automatic Image Analysis
| 분야 | 03.01 : 금속-기계적 시험;가열 및 저온시험;금속 조직학 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 적용범위 | 1.1 These test methods are used to determine grain size from measurements of grain intercept lengths, intercept counts, intersection counts, grain boundary length, and grain areas. 1.2 These measurements are made with a semiautomatic digitizing tablet or by automatic image analysis using an image of the grain structure produced by a microscope. 1.3 These test methods are applicable to any type of grain structure or grain size distribution as long as the grain boundaries can be clearly delineated by etching and subsequent image processing, if necessary. 1.4 These test methods are applicable to measurement of other grain-like microstructures, such as cell structures. 1.5 This standard deals only with the recommended test methods and nothing in it should be construed as defining or establishing limits of acceptability or fitness for purpose of the materials tested. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.7 The sections appear in the following order:
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 국제분류(ICS)코드 | 13.300 : 위험물에 대한 보호 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| 페이지수 | 24 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Edition | 97(2015) |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM E1382-97(2023) | Standard Test Methods for Determining Average Grain Size Using Semiautomatic and Automatic Image Analysis | 2023-04-01 | 표준 |
| 2 | ASTM E1382-97(2015) | Standard Test Methods for Determining Average Grain Size Using Semiautomatic and Automatic Image Analysis | 2015-10-01 | 구판 |
| 3 | ASTM E1382-97(2010) | Standard Test Methods for Determining Average Grain Size Using Semiautomatic and Automatic Image Analysis | 2010-11-01 | 구판 |
| 4 | ASTM E1382-97(2004) | Standard Test Methods for Determining Average Grain Size Using Semiautomatic and Automatic Image Analysis | 2004-11-01 | 구판 |
| 5 | ASTM E1382-97 | Standard Test Methods for Determining Average Grain Size Using Semiautomatic and Automatic Image Analysis | 1997-04-10 | 구판 |
관련상품이 존재하지 않습니다.
ASTM C1161-18 - Standard Test Method for Flexural Strength of Advanced Ceramics at Ambient Temperature 상세보기
ASTM C372-94(2016) - Standard Test Method for Linear Thermal Expansion of Porcelain Enamel and Glaze Frits and Fired Ceramic Whiteware Products by the Dilatometer Method 상세보기
ASTM C408-88(2016) - Standard Test Method for Thermal Conductivity of Whiteware Ceramics 상세보기
ASTM C20-00(2015) - Standard Test Methods for Apparent Porosity, Water Absorption, Apparent Specific Gravity, and Bulk Density of Burned Refractory Brick and Shapes by Boiling Water 상세보기
ASTM E112-13 - Standard Test Methods for Determining Average Grain Size 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
