관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
구판
판매
Standard Test Method for Determining Aerobic Biodegradation of Plastics Buried in Sandy Marine Sediment under Controlled Laboratory Conditions
| 분야 | 08.03 : 플라스틱 (Ⅲ) |
|---|---|
| 적용범위 | 1.1 This test method determines the biodegradation level of plastic materials exposed to laboratory conditions that simulate the environment found in the sandy tidal zone. 1.2 The tidal zone, that is, the part of the coast affected by the tides and movement of the waves, is the borderline between sea and land, frequently a sandy area that is kept constantly damp by the lapping of the waves. Stony and rocky shorelines also exist. 1.3 Plastic marine debris is frequently washed up in this habitat where it must be removed in order to restore the original landscape. 1.4 It is of interest to know the biodegradation behavior of plastics when exposed to conditions simulating this habitat, because this information can help in predicting the time needed for the biodegradation of the litter. 1.5 Biodegradation is determined by measuring the CO2 evolved by the plastic material when exposed to a sediment kept wet with salt-water in a reactor, to simulate the tidal zone. 1.6 Marine fresh-water habitats (for example, those found in brackish waters and estuaries) are not considered by this standard. 1.7 Reports shall clearly state the percentage of net CO2 generation for both the test and reference samples at the completion of the test. Furthermore, in the laboratory reports, the results shall not be extrapolated beyond the actual duration of the test. Note 1: There is no known ISO equivalent to this standard. 1.8 Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
| 국제분류(ICS)코드 | 83.080.01 : 플라스틱 일반 |
| 페이지수 | 5 |
| Edition | 15 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM D7991-22 | Standard Test Method for Determining Aerobic Biodegradation of Plastics Buried in Sandy Marine Sediment under Controlled Laboratory Conditions | 2022-05-01 | 표준 |
| 2 | ASTM D7991-22 REDLINE | Standard Test Method for Determining Aerobic Biodegradation of Plastics Buried in Sandy Marine Sediment under Controlled Laboratory Conditions | 2022-05-01 | 표준 |
| 3 | ASTM D7991-15 | Standard Test Method for Determining Aerobic Biodegradation of Plastics Buried in Sandy Marine Sediment under Controlled Laboratory Conditions | 2015-09-01 | 구판 |
관련상품이 존재하지 않습니다.
ISO 19679:2020 - Plastics — Determination of aerobic biodegradation of non-floating plastic materials in a seawater/sediment interface — Method by analysis of evolved carbon dioxide 상세보기
ISO 22766:2020 - Plastics — Determination of the degree of disintegration of plastic materials in marine habitats under real field conditions 상세보기
ISO 22404:2019 - Plastics — Determination of the aerobic biodegradation of non-floating materials exposed to marine sediment — Method by analysis of evolved carbon dioxide 상세보기
ISO 22403:2020 - Plastics — Assessment of the intrinsic biodegradability of materials exposed to marine inocula under mesophilic aerobic laboratory conditions — Test methods and requirements 상세보기
ASTM D7473/D7473M-21 REDLINE - Standard Test Method for Weight Attrition of Non-floating Plastic Materials by Open System Aquarium Incubations 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
