관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
구판
판매
Standard Test Method for Pitting or Crevice Corrosion of Metallic Surgical Implant Materials
| 분야 | 13.01 : 의료기, 외과용 도구 및 장비 |
|---|---|
| 적용범위 | 1.1 This test method covers the determination of resistance to either pitting or crevice corrosion of metals and alloys from which surgical implants will be produced. It is a modified version of an established test2 and is used as a screening test to rank surgical implant alloys in order of their resistance to localized corrosion. 1.2 This test method applies only to passive metals and alloys. Nonpassive alloys (other than noble alloys) are susceptible to general corrosion and are not normally suitable for implant use. 1.3 This test method is intended for use as a laboratory screening test for metals and alloys which undergo pitting or crevice corrosion, or both. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
| 국제분류(ICS)코드 | 11.040.40 : 외과. 보철술. 교정술용 이식 |
| 페이지수 | 7 |
| Edition | 04(2014) |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM F746-04(2021) | Standard Test Method for Pitting or Crevice Corrosion of Metallic Surgical Implant Materials | 2021-08-01 | 표준 |
| 2 | ASTM F746-04(2014) | Standard Test Method for Pitting or Crevice Corrosion of Metallic Surgical Implant Materials | 2014-10-01 | 구판 |
| 3 | ASTM F746-04(2009)e1 | Standard Test Method for Pitting or Crevice Corrosion of Metallic Surgical Implant Materials | 2009-12-01 | 구판 |
| 4 | ASTM F746-04 | Standard Test Method for Pitting or Crevice Corrosion of Metallic Surgical Implant Materials | 2004-10-01 | 구판 |
| 5 | ASTM F746-87(1999) | Standard Test Method for Pitting or Crevice Corrosion of Metallic Surgical Implant Materials | 1999-10-10 | 구판 |
관련상품이 존재하지 않습니다.
ASTM NACE/ASTMG193-12d - Standard Terminology and Acronyms Relating to Corrosion 상세보기
ASTM B368-09(2014) - Standard Test Method for Copper-Accelerated Acetic Acid-Salt Spray (Fog) Testing (CASS Test) 상세보기
ASTM G61-86(2018) - Standard Test Method for Conducting Cyclic Potentiodynamic Polarization Measurements for Localized Corrosion Susceptibility of Iron-, Nickel-, or Cobalt-Based Alloys 상세보기
ASTM F2081-06(2017) - Standard Guide for Characterization and Presentation of the Dimensional Attributes of Vascular Stents 상세보기
ASTM F2079-09(2017) - Standard Test Method for Measuring Intrinsic Elastic Recoil of Balloon-Expandable Stents 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
