관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
구판
판매
Standard Test Method for Tear Resistance (Graves Tear) of Plastic Film and Sheeting
| 분야 | 08.01 : 플라스틱 (Ⅰ) |
|---|---|
| 적용범위 | 1.1 This test method2 covers the determination of the tear resistance of flexible plastic film and sheeting at very low rates of loading, 51 mm (2 in.)/min. and is designed to measure the force to initiate tearing. The specimen geometry of this test method produces a stress concentration in a small area of the specimen. The maximum stress, usually found near the onset of tearing, is recorded as the tear resistance in newtons (or pounds-force). The method is not applicable for film or sheeting material where brittle failures occur during testing or where maximum extension is greater than 101.6 mm (4 in.). 1.1.1 Although resistance to tear can be expressed in newtons per microns, (pounds-force per mil) of specimen thickness, this is only advisable where correlation for the particular material being tested has been established. In most cases, comparison between films of dissimilar thickness is not valid. Note 1—Film has been arbitrarily defined as sheeting having nominal thickness not greater than 0.25 mm (0.010 in.). 1.2 Constant-Rate-of-Grip Separation Test—This test method employs a constant rate of separation of the grips holding the test specimen. 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are provided for information only. |
| 국제분류(ICS)코드 | 83.140.10 : 필름 및 시트 |
| 페이지수 | 4 |
| Edition | 13 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ASTM D1004-21 | Standard Test Method for Tear Resistance (Graves Tear) of Plastic Film and Sheeting | 2021-01-15 | 표준 |
| 2 | ASTM D1004-21 REDLINE | Standard Test Method for Tear Resistance (Graves Tear) of Plastic Film and Sheeting | 2021-01-15 | 표준 |
| 3 | ASTM D1004-13 REDLINE | Standard Test Method for Tear Resistance (Graves Tear) of Plastic Film and Sheeting | 2013-04-01 | 구판 |
| 4 | ASTM D1004-13 | Standard Test Method for Tear Resistance (Graves Tear) of Plastic Film and Sheeting | 2013-04-01 | 구판 |
| 5 | ASTM D1004-09 | Standard Test Method for Tear Resistance (Graves Tear) of Plastic Film and Sheeting | 2009-05-01 | 구판 |
| 6 | ASTM D1004-08 | Standard Test Method for Tear Resistance (Graves Tear) of Plastic Film and Sheeting | 2008-11-01 | 구판 |
| 7 | ASTM D1004-07 | Standard Test Method for Tear Resistance (Graves Tear) of Plastic Film and Sheeting | 2007-04-01 | 구판 |
| 8 | ASTM D1004-03 | Standard Test Method for Initial Tear Resistance of Plastic Film and Sheeting | 2003-01-10 | 구판 |
| 9 | ASTM D1004-94a(2003) | Standard Test Method for Initial Tear Resistance of Plastic Film and Sheeting | 2003-01-10 | 구판 |
| 10 | ASTM D1004-94a | Standard Test Method for Initial Tear Resistance of Plastic Film and Sheeting | 1994-01-01 | 구판 |
관련상품이 존재하지 않습니다.
ASTM D638-14 - Standard Test Method for Tensile Properties of Plastics 상세보기
ASTM D882-18 - Standard Test Method for Tensile Properties of Thin Plastic Sheeting 상세보기
ISO 527-1:2019 - Plastics — Determination of tensile properties — Part 1: General principles 상세보기
ASTM D651(1984 Edition) - STANDARD TEST METHOD FOR TENSILE STRENGTH OF MOLDED ELECTRICAL INSULATING MATERIALS 상세보기
ASTM D3431(1987 Edition) - STANDARD TEST METHOD FOR TRACE NITROGEN IN LIQUID PETROLEUM HYDROCARBONS (MICROCOULOMETRIC METHOD) 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
