관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
분야 | 05.01 : 석유제품 및 윤활유 (Ⅰ) |
---|---|
적용범위 | 1.1 This test method covers the determination of the amount of carbon residue (Note 1) left after evaporation and pyrolysis of an oil, and it is intended to provide some indication of relative coke-forming propensity. This test method is generally applicable to relatively nonvolatile petroleum products which partially decompose on distillation at atmospheric pressure. This test method also covers the determination of carbon residue on 10% (V/V) distillation residues (see Section 10). Petroleum products containing ash-forming constituents as determined by Test Method D 482 Note 1—The term carbon residue is used throughout this test method to designate the carbonaceous residue formed during evaporation and pyrolysis of a petroleum product. The residue is not composed entirely of carbon, but is a coke which can be further changed by pyrolysis. The term carbon residue is continued in this test method only in deference to its wide common usage. Note 2—Values obtained by this test method are not numerically the same as those obtained by Test Method D 189 Note 3—In diesel fuel, the presence of alkyl nitrates such as amyl nitrate, hexyl nitrate, or octyl nitrate, causes a higher carbon residue value than observed in untreated fuel, which can lead to erroneous conclusions as to the coke-forming propensity of the fuel. The presence of alkyl nitrate in the fuel can be detected by Test Method D 4046 Note 4—The test procedure in Section 10 is being modified to allow the use of a 100–mL volume automated distillation apparatus. No precision data is available for the procedure at this time, but a round robin is being planned to develop precision data. The 250–mL volume bulb distillation method described in Section 10 for determining carbon residue on a 10 % distillation residue is considered the referee test. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. |
국제분류(ICS)코드 | |
페이지수 | 9 |
Edition | 09 |
No. | 표준번호 | 표준명 | 발행일 | 상태 |
---|---|---|---|---|
1 | ASTM D524-15(2019) | Standard Test Method for Ramsbottom Carbon Residue of Petroleum Products | 2019-12-01 | 표준 |
2 | ASTM D524-15 | Standard Test Method for Ramsbottom Carbon Residue of Petroleum Products | 2015-06-01 | 구판 |
3 | ASTM D524-15 REDLINE | Standard Test Method for Ramsbottom Carbon Residue of Petroleum Products | 2015-06-01 | 구판 |
4 | ASTM D524-10 | Standard Test Method for Ramsbottom Carbon Residue of Petroleum Products | 2010-07-01 | 구판 |
5 | ASTM D524-09 | Standard Test Method for Ramsbottom Carbon Residue of Petroleum Products | 2009-06-01 | 구판 |
6 | ASTM D524-04 | Standard Test Method for Ramsbottom Carbon Residue of Petroleum Products | 2004-11-01 | 구판 |
7 | ASTM D524-03 | Standard Test Method for Ramsbottom Carbon Residue of Petroleum Products | 2003-09-10 | 구판 |
8 | ASTM D524-00 | Standard Test Method for Ramsbottom Carbon Residue of Petroleum Products | 2000-04-10 | 구판 |
9 | ASTM D524-00e1 | Standard Test Method for Ramsbottom Carbon Residue of Petroleum Products | 2000-04-10 | 구판 |
10 | ASTM D524-88 | Standard Test Method for Ramsbottom Carbon Residue of Petroleum Products | 구판 |
관련상품이 존재하지 않습니다.
함께 구입한 상품이 존재하지 않습니다.
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기