관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
분야 | 01.03 : 철강-강판, 강대 및 강선 |
---|---|
적용범위 | 1.1 These practices cover the following five tests: 1.1.1 Practice A— Oxalic Acid Etch Test for Classification of Etch Structures of Austenitic Stainless Steels (Sections 3 to 7, inclusive), 1.1.2 Practice B—Ferric Sulfate-Sulfuric Acid Test for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels (Sections 8 to 14, inclusive), 1.1.3 Practice C—Nitric Acid Test for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels (Sections 15 to 21, inclusive), 1.1.4 Practice E—Copper-Copper Sulfate-Sulfuric Acid Test for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels (Sections 22 to 31, inclusive), and 1.1.5 Practice F—Copper-Copper Sulfate-50% Sulfuric Acid Test for Detecting Susceptibility to Intergranular Attack in Molybdenum-Bearing Cast Austenitic Stainless Steels (Sections 32 to 38, inclusive). 1.2 The following factors govern the application of these practices: 1.2.1 Susceptibility to intergranular attack associated with the precipitation of chromium carbides is readily detected in all six tests. 1.2.2 Sigma phase in wrought chromium-nickel-molybdenum steels, which may or may not be visible in the microstructure, can result in high corrosion rates only in nitric acid. 1.2.3 Sigma phase in titanium or columbium stabilized alloys and cast molybdenum bearing stainless alloys, which may or may not be visible in the microstructure, can result in high corrosion rates in both the nitric acid and ferric sulfate-sulfuric acid solutions. 1.3 The oxalic acid etch test is a rapid method of identifying, by simple etching, those specimens of certain stainless steel grades which are essentially free of susceptibility to intergranular attack associated with chromium carbide precipitates. These specimens will have low corrosion rates in certain corrosion tests and therefore can be eliminated (screened) from testing as "acceptable." 1.4 The ferric sulfate-sulfuric acid test, the copper-copper sulfate-50% sulfuric acid test, and the nitric acid test are based on weight loss determinations and, thus, provide a quantitative measure of the relative performance of specimens evaluated. In contrast, the copper-copper sulfate-16% sulfuric acid test is based on visual examination of bend specimens and, therefore, classifies the specimens only as acceptable or non-acceptable. 1.5 In most cases either the 24-h copper-copper sulfate-16% sulfuric acid test or the 120-h ferric sulfate-sulfuric acid test, combined with the oxalic acid etch test, will provide the required information in the shortest time. All stainless grades listed in the accompanying table may be evaluated in these combinations of screening and corrosion tests, except those specimens of molybdenum-bearing grades (for example 316, 316L, 317, and 317L), which represent steel intended for use in nitric acid environments. 1.6 The 240-h nitric acid test must be applied to stabilized and molybdenum-bearing grades intended for service in nitric acid and to all stainless steel grades which might be subject to end grain corrosion in nitric acid service. 1.7 Only those stainless steel grades are listed in Table 1 for which data on the application of the oxalic acid etch test and on their performance in various quantitative evaluation tests are available. 1.8 Extensive test results on various types of stainless steels evaluated by these practices have been published in Ref (1). 1.9 The values stated in SI units are to be regarded as standard. The inch-pound equivalents are in parentheses and may be approximate. 1.10 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. (Specific precautionary statements are given in 5.6, 11.1.1, 11.1.9, and 35.1.) |
국제분류(ICS)코드 | |
페이지수 | 17 |
Edition | 02ae2 |
No. | 표준번호 | 표준명 | 발행일 | 상태 |
---|---|---|---|---|
1 | ASTM A262-15(2021) | Standard Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels | 2021-09-01 | 표준 |
2 | ASTM A262-15 | Standard Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels | 2015-09-01 | 구판 |
3 | ASTM A262-15 REDLINE | Standard Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels | 2015-09-01 | 구판 |
4 | ASTM A262-14 | Standard Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels | 2014-07-01 | 구판 |
5 | ASTM A262-13 | Standard Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels | 2013-05-01 | 구판 |
6 | ASTM A262-10 | Standard Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels | 2010-04-01 | 구판 |
7 | ASTM A262-02a(2008) | Standard Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels | 2008-03-01 | 구판 |
8 | ASTM A262-02ae2 | Standard Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels | 2002-11-10 | 구판 |
9 | ASTM A262-02ae3 | Standard Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels | 2002-11-10 | 구판 |
10 | ASTM A262-02ae1 | Standard Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels | 2002-11-10 | 구판 |
11 | ASTM A262-02a | Standard Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels | 2002-11-10 | 구판 |
12 | ASTM A262-02 | Standard Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels | 2002-06-10 | 구판 |
13 | ASTM A262-98 | Standard Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels | 2001-09-10 | 구판 |
14 | ASTM A262-01 | Standard Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels | 2001-09-10 | 구판 |
관련상품이 존재하지 않습니다.
함께 구입한 상품이 존재하지 않습니다.
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기