관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
분야 | 14.04 : 시험소 기계 장치; 재료의 퇴화; 여과; SI; 화재 안전 |
---|---|
적용범위 | 1.1 This practice covers the basic principles and operating procedures for using xenon arc light and water apparatus intended to reproduce the weathering effects that occur when materials are exposed to sunlight (either direct or through window glass) and moisture as rain or dew in actual use. This practice is limited to the procedures for obtaining, measuring, and controlling conditions of exposure. A number of exposure procedures are listed in an appendix; however, this practice does not specify the exposure conditions best suited for the material to be tested. Note 1--Practice G151 describes performance criteria for all exposure devices that use laboratory light sources. This practice replaces Practice G26, which describes very specific designs for devices used for xenon-arc exposures. The apparatus described in Practice G26 is covered by this practice. 1.2 Test specimens are exposed to filtered xenon arc light under controlled environmental conditions. Different types of xenon arc light sources and different filter combinations are described. 1.3 Specimen preparation and evaluation of the results are covered in ASTM methods or specifications for specific materials. General guidance is given in Practice G 151 and ISO 4892-1. More specific information about methods for determining the change in properties after exposure and reporting these results is described in ISO 4582. 1.4 The values stated in SI units are to be regarded as the standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.5.1 Should any ozone be generated from the operation of the lamp(s), it shall be carried away from the test specimens and operating personnel by an exhaust system. 1.6 This practice is technically similar to the following ISO documents: ISO 4892-2, ISO 1134, ISO 105 B02, ISO 105 B04, ISO 105 B05, and ISO 105 B06. |
국제분류(ICS)코드 | |
페이지수 | 7 |
Edition | 00 |
No. | 표준번호 | 표준명 | 발행일 | 상태 |
---|---|---|---|---|
1 | ASTM G155-21 | Standard Practice for Operating Xenon Arc Lamp Apparatus for Exposure of Materials | 2021-07-01 | 표준 |
2 | ASTM G155-21 REDLINE | Standard Practice for Operating Xenon Arc Lamp Apparatus for Exposure of Materials | 2021-07-01 | 표준 |
3 | ASTM G155-13 REDLINE | Standard Practice for Operating Xenon Arc Light Apparatus for Exposure of Non-Metallic Materials | 2013-06-01 | 구판 |
4 | ASTM G155-13 | Standard Practice for Operating Xenon Arc Light Apparatus for Exposure of Non-Metallic Materials | 2013-06-01 | 구판 |
5 | ASTM G155-05a | Standard Practice for Operating Xenon Arc Light Apparatus for Exposure of Non-Metallic Materials | 2005-10-01 | 구판 |
6 | ASTM G155-05 | Standard Practice for Operating Xenon Arc Light Apparatus for Exposure of Non-Metallic Materials | 2005-07-01 | 구판 |
7 | ASTM G155-04a | Standard Practice for Operating Xenon Arc Light Apparatus for Exposure of Non-Metallic Materials | 2004-10-01 | 구판 |
8 | ASTM G155-04 | Standard Practice for Operating Xenon Arc Light Apparatus for Exposure of Non-Metallic Materials | 2004-02-01 | 구판 |
9 | ASTM G155-00a | Standard Practice for Operating Xenon Arc Light Apparatus for Exposure of Non-Metallic Materials | 2000-08-10 | 구판 |
10 | ASTM G155-00 | Standard Practice for Operating Xenon Arc Light Apparatus for Exposure of Non-Metallic Materials | 2000-08-10 | 구판 |
11 | ASTM G155-00ae1 | Standard Practice for Operating Xenon Arc Light Apparatus for Exposure of Non-Metallic Materials | 2000-08-10 | 구판 |
관련상품이 존재하지 않습니다.
함께 구입한 상품이 존재하지 않습니다.
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기