관심표준 등록 : 표준업데이트 시 알림을 받을 수 있습니다.
PDF : 직접 파일 다운로드 및 인쇄 (마이페이지 확인)
PRINT : 인쇄본 우편발송, 2~3일 소요(PDF파일 미제공)
표준
판매
Geometrical product specifications (GPS) — Dimensional and geometrical tolerances for moulded parts — Part 3: General dimensional and geometrical tolerances and machining allowances for castings using ± tolerances for indicated dimensions
| 분야 | ISO/TC 213 : Dimensional and geometrical product specifications and verification |
|---|---|
| 적용범위 | This document specifies general dimensional and geometrical tolerances as well as machining allowance grades for castings using ± tolerances for indicated dimensions as delivered to the purchaser according to ISO/TS 8062-2. It is applicable for tolerancing of dimensions and geometry of castings in all cast metals and their alloys produced by various casting manufacturing processes. This document does not apply to 3D CAD models used without indicated dimensions. This document applies to both general dimensional and general geometrical tolerances (referred to in or near the title block of the drawing), unless otherwise specified and where specifically referred to on the drawing by one of the references in Clause 11. The dimensional tolerances covered by this document are tolerances for linear dimensions. The geometrical tolerances covered by this document are tolerances for: — straightness; — flatness; — roundness; — parallelism; — perpendicularity; — symmetry; — coaxiality. This document does not cover other position tolerances, angular dimensional tolerances or cylindricity tolerances. This document can be used for the selection of tolerance values for individual indications. |
| 국제분류(ICS)코드 | 17.040.10 : 공차 및 끼워 맞춤 |
| 페이지수 | 34 |
| Edition | 2 |
| No. | 표준번호 | 표준명 | 발행일 | 상태 |
|---|---|---|---|---|
| 1 | ISO 8062-3:2023 | Geometrical product specifications (GPS) — Dimensional and geometrical tolerances for moulded parts — Part 3: General dimensional and geometrical tolerances and machining allowances for castings using ± tolerances for indicated dimensions | 2023-02-15 | 표준 |
| 2 | ISO 8062-3:2007/Cor 1:2009 | Geometrical product specifications (GPS) — Dimensional and geometrical tolerances for moulded parts — Part 3: General dimensional and geometrical tolerances and machining allowances for castings — Technical Corrigendum 1 | 2009-01-14 | 구판 |
| 3 | ISO 8062-3:2007 | Geometrical product specifications (GPS) — Dimensional and geometrical tolerances for moulded parts — Part 3: General dimensional and geometrical tolerances and machining allowances for castings | 2007-05-31 | 구판 |
ISO 8062-1:2007 - Geometrical product specifications (GPS) — Dimensional and geometrical tolerances for moulded parts — Part 1: Vocabulary 상세보기
ISO/TS 8062-2:2013 - Geometrical product specifications (GPS) — Dimensional and geometrical tolerances for moulded parts — Part 2: Rules 상세보기
ISO 8062-4:2023 - Geometrical product specifications (GPS) — Dimensional and geometrical tolerances for moulded parts — Part 4: Rules and general tolerances for castings using profile tolerancing in a general datum system 상세보기
ISO 8015:2011 - Geometrical product specifications (GPS) — Fundamentals — Concepts, principles and rules 상세보기
ISO 9227:2022 - Corrosion tests in artificial atmospheres — Salt spray tests 상세보기
ISO 21204:2020 - Geometrical product specifications (GPS) — Transition specification 상세보기
ISO 19598:2016 - Metallic coatings — Electroplated coatings of zinc and zinc alloys on iron or steel with supplementary Cr(VI)-free treatment 상세보기
ISO 3302-2:2022 - Rubber — Tolerances for products — Part 2: Geometrical tolerances 상세보기
IEC TS 63134:2020 - Active assisted living (AAL) use cases 상세보기
IEC 60034-5:2020 RLV - Rotating electrical machines - Part 5: Degrees of protection provided by the integral design of rotating electrical machines (IP code) - Classification 상세보기
KS B ISO TS 25740-1 - 에스컬레이터 및 무빙워크에 대한 안전요건 — 제1부: 세계공통 필수 안전요건(GESRs) 상세보기
KS B ISO TS 8100-21 - 승객 및 화물 운송용 엘리베이터 —제21부: 세계공통 필수안전요건(GESRs)을 충족하는 세계공통 안전 파라미터(GSPs) 상세보기
KS C IEC TS 62872 - 산업 시설과 스마트 그리드 사이의 산업 공정 측정, 제어 및 자동화 시스템 인터페이스 상세보기
KS표준
핸드북
